Re: ubxtool

[Gary E. Miller]

Yo address@hidden!

I got no such email.  The email you referred to did not include
my email address, or gpsd-users.

On Sat, 11 Apr 2020 08:35:17 -0400
<address@hidden> wrote:

> Gary,
> 
> Any word on the data I sent you on GPSD sending RTCM to the F9P?
> 
> -----Original Message-----
> From: address@hidden <address@hidden> 
> Sent: Tuesday, April 7, 2020 1:39 PM
> To: address@hidden
> Subject: RE: ubxtool
> 
> Gary,
> 
> Got the analyzer hooked and have done captures from Windows to GPS (
> rtklib's strsrv )  and GPSD to GPS.
> Not sure how you wanted the data so to start I did a hex dump to a
> binary file.
> Description of the attached files.
> FAIL-F9P...       contains the GPSD RTCM data.      RTK LED was off
> Succes-F9P...  contains the STRSRV RTCM data.   RTK LED was  blinking 
> 
> F9P_UART_TX--PI   contains F9P send to the PI, during the Fail session
> F9P-UART_TX--PC   contains F9P send to the PCX , during the Success
> session
> 
> 
> I use the Saleae analyzer so if needed I can dump the whole analysis
> to a file that will contain both the digital and analog signals.
> You can download their software (free) and "replay" the log file .
> 
> Let me know if you need any other data.
> 
> Regards,
> Rick
> 
> -----Original Message-----
> From: gpsd-users <gpsd-users-bounces+rhowitt=address@hidden> On
> Behalf Of address@hidden
> Sent: Monday, April 6, 2020 10:33 AM
> To: 'Gary E. Miller' <address@hidden>; 'gpsd users'
> <address@hidden> Subject: RE: ubxtool
> 
> Gary,
> 
> I am working on putting an analyzer on the GPS dev board. But ran
> into a problem that the breakout pin that is suppose to be showing RX
> data into the board is not showing any data.  Even though RTKlib's
> strsrv is sending data to the GPS and the GPS is blinking it's RTK
> LED.  Currently the dev board is based on USB, where it breaks out
> the serial traffic from the USB. 
> 
> So working on solution to by-pass USB altogether and just use serial.
> 
> -----Original Message-----
> From: gpsd-users <gpsd-users-bounces+rhowitt=address@hidden> On
> Behalf Of Gary E. Miller
> Sent: Saturday, April 4, 2020 8:48 PM
> To: 'gpsd users' <address@hidden>
> Subject: Re: ubxtool
> 
> Yo address@hidden!
> 
> On Sat, 4 Apr 2020 20:38:47 -0400
> <address@hidden> wrote:
> 
> > Yes , -R was used for both.
> > 
> > gpspipe -R -n 300 localhost:2947 -o /api/gpsd_ntrip.dat gpspipe -R
> > -n 300 localhost:2947 -o /api/gpsd_ntrip1.dat  
> 
> Good.  As I said in the message before the one just just replied to:
> 
> -- No point running gpsd with different debug levels if you don't
> send the -- debug output.
> 
> > Was there RTCM3 data in the log file?  
> 
> As I said in the message before the one just just replied to:
> 
> -- > gpsd:PROG: RTCM3: unknown type 1075, length 376
> -- > gpsd:DATA: packet type 18 from ntrip://rhowittRpi:Walfer2019
> with --
> -- gpsd got an RTCM3 type 1075 packet.
> 
> And I also said:
> 
> -- Ignoring gpsd_ntrip.data as you did not send the matching output.
> --
> -- Looking at gpsd_ntrip1.dat, looks like the same data types as
> before.




RGDS
GARY
---------------------------------------------------------------------------
Gary E. Miller Rellim 109 NW Wilmington Ave., Suite E, Bend, OR 97703
        address@hidden  Tel:+1 541 382 8588

            Veritas liberabit vos. -- Quid est veritas?
    "If you can't measure it, you can't improve it." - Lord Kelvin

pgpOVRjTNqler.pgp
Description: OpenPGP digital signature