Re: WG: [Swarm-Support] Compiling swarm-2.1.148.20040122

[Giovanni Maniscalco Basile]

Dear Pj,

thanks, everything worked OK.

I also donwloaded from your Swarm site the gzipped Village6 code.
It compiled all right, but at runtime it complained that it didn't find some data files: hydro.data
degrade.data, etc. I got some of them from an earlier version of the simulation, but no all the needed files.
Do you know where I can find them?

Thank you again.

Giovanni Maniscalco Basile

Il sab, 2004-03-27 alle 17:14, Paul Johnson ha scritto:
>  Here's the error in your output:
>
> gperf: command not found
>
> That means you should install the package "gperf"
>
> please note I do not mean "my_java_dir" literally. I mean to point at 
> where your system has java installed.  On my systems, it is 
> /usr/java/j2sdk1.4.2_03
>
> Giovanni Maniscalco Basile wrote:
>
> > I tried to compile swarm-2.1.148.20041022 on a SuSE 9.0 system 
> > following the instructions given by PJ:
> >
> > #cd swarm-2.1.148
> > # mkdir builddir
> > # cd builddir
> > # CC=/usr/bin/gcc ../configure --prefix=/usr --enable-subdirs 
> > --with-defaultdir=/usr --with-jdkdir=my_java_dir
> >
> > then
> >
> > # make
> >
> > the make process gave the following error:
> >
> > /home/maniba/swarm/swarm-2.1.148.20040122/builddir/_common.elc
> > Done
> > Wrote /home/maniba/swarm/swarm-2.1.148.20040122/builddir/_protocol.elc
> > Done
> > Wrote /home/maniba/swarm/swarm-2.1.148.20040122/builddir/_interface.elc
> > Done
> > Wrote /home/maniba/swarm/swarm-2.1.148.20040122/builddir/src/_getters.elc
> > Done
> > cc1: warning: "-Wno-protocol" is valid for ObjC but not for C/C++
> > cc1: warning: "-fgnu-runtime" is valid for ObjC but not for C/C++
> > cc1: warning: "-Wno-protocol" is valid for ObjC but not for C/C++
> > cc1: warning: "-fgnu-runtime" is valid for ObjC but not for C/C++
> > cc1: warning: "-Wno-protocol" is valid for ObjC but not for C/C++
> > cc1: warning: "-fgnu-runtime" is valid for ObjC but not for C/C++
> > ../../../src/misc/xmalloc.c:10: warning: empty declaration
> > ../../../src/misc/xmalloc.c:11: warning: empty declaration
> > ../../../src/misc/xmalloc.c:12: warning: empty declaration
> > ../../../src/misc/xmalloc.c:13: warning: empty declaration
> > Wrote 
> > /home/maniba/swarm/swarm-2.1.148.20040122/builddir/src/defobj/_modulemap.elc
> > Done
> > /bin/sh: line 1: gperf: command not found
> > make[5]: *** [../../../src/defobj/modulemap.c] Error 127
> > make[4]: *** [all] Error 2
> > make[3]: *** [all-recursive] Error 1
> > make[2]: *** [all] Error 2
> > make[1]: *** [all-recursive] Error 1
> > make: *** [all] Error 2
> >
> >
> > I attach the config.log and Makefile
> >
> > Thanks
> >
> > Giovanni Maniscalco Basile
> >
> > P.S. does it exists a newer version of Swarm?
> > If so, where is it?
> >
> > GMB
> >
> >------------------------------------------------------------------------
> >
>
> _______________________________________________
> Support mailing list
> address@hidden
> http://www.swarm.org/mailman/listinfo/support