On Fri, Jan 29, 2010 at 6:43 PM, Jayson MacKiddie
<
address@hidden> wrote:
> Hello All,
>
> I'm compiling a BOM from the eagle schematic. Would anyone already happen to
> have this BOM ready to go?
>
> Regards,
> Jayson
>
>
> On Fri, Jan 29, 2010 at 11:50 AM, Mohammed Abukhalid
> <
address@hidden> wrote:
>>
>> Thanks Antoine that really sets my mind at ease!! That board's a good idea
>> to keep things neat.
>>
>> > Date: Thu, 28 Jan 2010 22:50:11 +0100
>> > Subject: Re: [Paparazzi-devel] power board
>> > From:
address@hidden
>> > To:
address@hidden
>> >
>> > well.... I've used home made PCBs, so no solder mask and I have tined
>> > the tracks, but I don't think you should have any problem
>> >
>> > here are pics of what I did
>> >
>> >
http://booz-dev.googlegroups.com/web/power_board_bot.jpg
>> >
http://booz-dev.googlegroups.com/web/power_board_bot.jpg
>> >
>> >
>> > On Thu, Jan 28, 2010 at 6:56 PM, Mohammed Abukhalid
>> > <
address@hidden> wrote:
>> > > Thanks for the reply! No its just 4 motors.. I was just saying the
>> > > range was
>> > > 6A-14A ... and in all probability we are going to be running well
>> > > below 14A.
>> > > The only concern that was raised was whether the traces on the pcb
>> > > could
>> > > handle it. But if you've done it before with the same board then we're
>> > > fine
>> > > for sure
>> > >
>> > >> Date: Thu, 28 Jan 2010 18:13:30 +0100
>> > >> Subject: Re: [Paparazzi-devel] power board
>> > >> From:
address@hidden
>> > >> To:
address@hidden
>> > >>
>> > >> the mosfet is rated 80 amps - I've made this board for my mikrokopter
>> > >> frame where the motors draw about the same current - you should be
>> > >> fine.
>> > >> or are you saying you are using 6 motors drawing each 14 amps ? in
>> > >> which case you'd be just over th limit
>> > >>
>> > >> On Thu, Jan 28, 2010 at 5:57 PM, Mohammed Abukhalid
>> > >> <
address@hidden> wrote:
>> > >> > Hi all,
>> > >> >
>> > >> > I was wondering if anyone is familiar with the Booz power board
>> > >> > design
>> > >> > enough to know its current limitations. Our motors are supposed to
>> > >> > use
>> > >> > 6-14A
>> > >> > of current... Anyone know if the traces on booz power board can
>> > >> > handle
>> > >> > that
>> > >> > much?
>> > >> >
>> > >> > Mohammed
>> > >> >
>> > >> > ________________________________
>> > >> > Spread the cheer with Messenger for mobile. Learn more.
>> > >> > _______________________________________________
>> > >> > Paparazzi-devel mailing list
>> > >> >
address@hidden
>> > >> >
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>> > >> >
>> > >> >
>> > >>
>> > >>
>> > >> _______________________________________________
>> > >> Paparazzi-devel mailing list
>> > >>
address@hidden
>> > >>
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>> > >
>> > > ________________________________
>> > > Tell the whole story with photos, right from your Messenger window.
>> > > Learn
>> > > how!
>> > > _______________________________________________
>> > > Paparazzi-devel mailing list
>> > >
address@hidden
>> > >
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>> > >
>> > >
>> >
>> >
>> > _______________________________________________
>> > Paparazzi-devel mailing list
>> >
address@hidden
>> >
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>>
>> ________________________________
>> Spread the cheer with Messenger for mobile. Learn more.
>> _______________________________________________
>> Paparazzi-devel mailing list
>>
address@hidden
>>
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>>
>
>
>
> --
> Jayson MacKiddie
>
> _______________________________________________
> Paparazzi-devel mailing list
>
address@hidden
>
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>
>
_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel