Re: [Discuss-gnuradio] Re g : Building gr-uhd and usrp2-firmware

[Morgan Redfield]

Did you install UHD before you built gnuradio?

You can follow the build guide here:
http://www.ettus.com/uhd_docs/manual/html/build.html

Morgan

On Thu, Jun 23, 2011 at 3:50 PM, sumitstop
<address@hidden> wrote:
>
> I am using ubuntu Lucid 10.04 LTS.
>
> Did the following thing
>
> Step-1 Installed all the dependencies for ubuntu Lucid 10.04 from the script
> given here
> http://gnuradio.org/redmine/projects/gnuradio/wiki/UbuntuInstall
>
> step-2 git clone http://gnuradio.org/git/gnuradio.git
> then
>
> step-3 git clone http://github.com/EttusResearch/UHD-Mirror.git
> after that
>
> step-4 cd gnuradio
> step-5 ./bootstrap
> step-6 ./configure
>
> I got following messages
> *********************************************************************
> The following components were skipped either because you asked not
> to build them or they didn't pass configuration checks:
>
> usrp2-firmware
>
> These components will not be built.
>
>
> *********************************************************************
> The following GNU Radio components have been successfully configured:
>
> config
> gruel
> volk
> gnuradio-core
> usrp
> usrp2
> gr-usrp
> gr-usrp2
> gr-msdd6000
> gr-audio
> gr-atsc
> gr-cvsd-vocoder
> gr-gpio
> gr-gsm-fr-vocoder
> gr-noaa
> gr-pager
> gr-radar-mono
> gr-radio-astronomy
> gr-trellis
> gr-video-sdl
> gr-wxgui
> gr-qtgui
> gr-sounder
> gr-utils
> gnuradio-examples
> grc
> docs
>
> You my now run the make command to build these components.
>
> *********************************************************************
> The following components were skipped either because you asked not
> to build them or they didn't pass configuration checks:
>
> gcell
> gr-gcell
> gr-comedi
> gr-uhd
>
> These components will not be built.
>
> Configured GNU Radio release v3.4.0-2-g081497e7 for build.
>
> **********************************************************************
>
> I searched a lot and found answer to many of questions
>
> From the following link(in the summary) i found that no need to build
> gr-comedi
> http://lists.gnu.org/archive/html/discuss-gnuradio/2006-06/msg00225.html
>
> Also in the following link I read that gcell and gr-gcell are needed only
> for IBM cell processor.
> http://www.ruby-forum.com/topic/201112
>
> So I want to ask what should I do to build
>
> gr-uhd and usrp2-firmware
>
> I also did
>
> ./configure --enable-gr-uhd
>
> but it shows following message
>
> checking for UHD... no
> gr-uhd requires libuhd 3.x.x
> configure: error: Component gr-uhd has errors; stopping.
>
> I also did
>
> ./configure --enable-usrp2-firmware
>
> and got following message
>
> checking whether byte ordering is bigendian... no
> checking for mb-gcc... no
> usrp2 firmware requires mb-gcc.  Not found
> configure: error: Component usrp2-firmware has errors; stopping.
> configure: error: ./configure.gnu failed for usrp2/firmware
>
> I saw several posts with the same problem but honestly I couldn't understand
> what to do next.
>
> Regards
>
>
>
>
> -----
> Sumit Kr.
> Research Assistant
> Communication Research center
> IIIT Hyderabad
> India
> --
> View this message in context: 
> http://old.nabble.com/Reg-%3A-Building-gr-uhd-and-usrp2-firmware-tp31915462p31915462.html
> Sent from the GnuRadio mailing list archive at Nabble.com.
>
>
> _______________________________________________
> Discuss-gnuradio mailing list
> address@hidden
> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>