[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Discuss-gnuradio] Re g : Building gr-uhd and usrp2-firmware
From: |
sumitstop |
Subject: |
[Discuss-gnuradio] Re g : Building gr-uhd and usrp2-firmware |
Date: |
Thu, 23 Jun 2011 15:50:53 -0700 (PDT) |
I am using ubuntu Lucid 10.04 LTS.
Did the following thing
Step-1 Installed all the dependencies for ubuntu Lucid 10.04 from the script
given here
http://gnuradio.org/redmine/projects/gnuradio/wiki/UbuntuInstall
step-2 git clone http://gnuradio.org/git/gnuradio.git
then
step-3 git clone http://github.com/EttusResearch/UHD-Mirror.git
after that
step-4 cd gnuradio
step-5 ./bootstrap
step-6 ./configure
I got following messages
*********************************************************************
The following components were skipped either because you asked not
to build them or they didn't pass configuration checks:
usrp2-firmware
These components will not be built.
*********************************************************************
The following GNU Radio components have been successfully configured:
config
gruel
volk
gnuradio-core
usrp
usrp2
gr-usrp
gr-usrp2
gr-msdd6000
gr-audio
gr-atsc
gr-cvsd-vocoder
gr-gpio
gr-gsm-fr-vocoder
gr-noaa
gr-pager
gr-radar-mono
gr-radio-astronomy
gr-trellis
gr-video-sdl
gr-wxgui
gr-qtgui
gr-sounder
gr-utils
gnuradio-examples
grc
docs
You my now run the make command to build these components.
*********************************************************************
The following components were skipped either because you asked not
to build them or they didn't pass configuration checks:
gcell
gr-gcell
gr-comedi
gr-uhd
These components will not be built.
Configured GNU Radio release v3.4.0-2-g081497e7 for build.
**********************************************************************
I searched a lot and found answer to many of questions
>From the following link(in the summary) i found that no need to build
gr-comedi
http://lists.gnu.org/archive/html/discuss-gnuradio/2006-06/msg00225.html
Also in the following link I read that gcell and gr-gcell are needed only
for IBM cell processor.
http://www.ruby-forum.com/topic/201112
So I want to ask what should I do to build
gr-uhd and usrp2-firmware
I also did
./configure --enable-gr-uhd
but it shows following message
checking for UHD... no
gr-uhd requires libuhd 3.x.x
configure: error: Component gr-uhd has errors; stopping.
I also did
./configure --enable-usrp2-firmware
and got following message
checking whether byte ordering is bigendian... no
checking for mb-gcc... no
usrp2 firmware requires mb-gcc. Not found
configure: error: Component usrp2-firmware has errors; stopping.
configure: error: ./configure.gnu failed for usrp2/firmware
I saw several posts with the same problem but honestly I couldn't understand
what to do next.
Regards
-----
Sumit Kr.
Research Assistant
Communication Research center
IIIT Hyderabad
India
--
View this message in context:
http://old.nabble.com/Reg-%3A-Building-gr-uhd-and-usrp2-firmware-tp31915462p31915462.html
Sent from the GnuRadio mailing list archive at Nabble.com.
- [Discuss-gnuradio] Re g : Building gr-uhd and usrp2-firmware,
sumitstop <=