paparazzi-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Paparazzi-devel] ADC channel for Gyro


From: Michel GORRAZ
Subject: Re: [Paparazzi-devel] ADC channel for Gyro
Date: Mon, 23 Jun 2008 22:43:41 +0200

It's really good to read that David, a great encouragement for me to carry on...

Many thanks

@+
Michel

2008/6/23 David Conger <address@hidden>:
Excellent, 

Thank you Michel, 
Also THANK YOU! ...  for taking such time to document the designs so well on the Wiki. 

When I first started my interest with Paparazzi Tiny1.3 was new...BOM, Pinout, even photos were scarce. I use your Wiki pages exclusively and many many times a day to refer to the pinouts, layouts etc. Questions asked of me are most often replied with URL right to your pages to the pinouts or images or notes. 

Well done. I'm sure many many people appreciate the time you spent to document so thoroughly. I may not find what I am looking for on the Wiki but I have to at the same time give credit that the latest designs are extremely well documented there.

Regards,
David

On Jun 23, 2008, at 12:57 PM, Michel GORRAZ wrote:

Hi,

The easiest way to connect a ADXRS300 on a Tiny v2 (or a Twog) is to use ADC5 on the "ADC2" connector
- GND on GND (pin #1)
- +5V on +5v (pin #2)
- Rateout on ADC5 (pin #5) => resistor bridge for 5v sensor is included for this ADC on the Tiny V2

And... that all !

Don't worry, ADC1 is probably alive :)

@+
Michel

2008/6/23 David Conger <address@hidden>:
Hello,

Thank you Michel. GTK. Can I ask a question related...

My Gyro is 5v (ADXRS300) with ST1, ST2, TEMP, 2.5V, RATE, GND, 5V..

Can someone please give the pins to connect to the Tiny on ADC2? 

5v is easy -> +5v on Tiny
GND -> GND on Tiny
....
Without any instructions on the Wiki about the connector and going by the funjet1.xml airframe file given I had it connected to ADC1 
GRYO ---- TINY
GND -> GND
RATE->ADC3
5V->+5v 
I hope I didn't damage ADC1 on the Tiny

Thank you,
-David

So, if I were to connect my 5v Gyro into 

On Jun 23, 2008, at 8:29 AM, Michel GORRAZ wrote:

Hi,
For sure, you can use this ADC with a Gyro (or  other analog sensor) but this is a 3.3v max input level, so if your gyro  is a 5v, don't forget the resistor bridge...or use  ADC5 or ADC6 : these inputs have their own on-board resistor bridge.

@+
Michel

2008/6/23 C Kuo <address@hidden>:

Hi guys


 I was wondering, on the "USB" port on TinyV2 has a ADC_7, could I use this
chaneel for connecting roll gyro?





Thanks

                                                                Chen


_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel


_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel


_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel


_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel



reply via email to

[Prev in Thread] Current Thread [Next in Thread]