yum remove sdcc
Removing:
sdcc
i686
3.0.0-0.fc14
@updates 49
M
Get SDCC 2.9.0 and follow instructions in
INSTALL.txt
cd gnuradio
./bootstrap
./configure
--enable-usrp --enable-gr-usr
config.status: executing depfiles
commands
*********************************************************************
The
following components were skipped either because you asked not
to build them
or they didn't pass configuration checks:
usrp2-firmware
These components will not be
built.
*********************************************************************
The
following GNU Radio components have been successfully configured:
config
gruel
volk
gnuradio-core
usrp
usrp2
gr-usrp
gr-usrp2
gr-msdd6000
gr-audio
gr-atsc
gr-cvsd-vocoder
gr-gpio
gr-gsm-fr-vocoder
gr-noaa
gr-pager
gr-radar-mono
gr-radio-astronomy
gr-trellis
gr-video-sdl
gr-wxgui
gr-qtgui
gr-sounder
gr-utils
gnuradio-examples
grc
docs
You my now run the make command to build these
components.
*********************************************************************
The
following components were skipped either because you asked not
to build them
or they didn't pass configuration checks:
gcell
gr-gcell
gr-comedi
gr-uhd
These components will not be built.
Configured GNU Radio release v3.4.0git-139-gf53fef3d for build.
make
make install
Patrik
----- Original Message -----
Sent: Sunday, May 15, 2011 21:01
Subject: [Discuss-gnuradio] F14 GR
traditional usrp install (no uhd)
Hi all,
I really screwed up today when I upgraded from F13 to
F14 result, no network, access denied to every device (RAID),
etc.
I was able to burn (backup) sources to disk and then
formatted from latest F14.
I run into probs when installing the traditional USRP1
without uhd. Configure seems to expect sdcc v2 but the latest is
3.
Another observation, configure used to build both
USRP1/2. Now USRP2 seems to be the only availabel by default, that is
understandable.
Snips from terminal output:
./configure --enable-usrp --enable-gr-usrp
configure: Using LIBUSB version 'libusb'
checking for
sdcc... sdcc -mmcs51 --no-xinit-opt
checking for asx8051... no
USRP
requires sdcc version 2. sdcc not found. See http://sdcc.sf.net
Unable to find firmware
compiler SDCC.
configure: error: Component usrp has errors;
stopping.
sdcc -v
SDCC :
mcs51/gbz80/z80/ds390/pic16/pic14/TININative/ds400/hc08 3.0.0 #6037 (Mar 20
2011) (Linux)
I suspect this is the problem, 2 vs 3?
Another snip from terminal
output:
./bootstrap
./configure
config.status: executing depfiles
commands
*********************************************************************
The
following components were skipped either because you asked not
to build
them or they didn't pass configuration checks:
usrp2-firmware
These components will not be built.
*********************************************************************
The
following GNU Radio components have been successfully configured:
config
gruel
volk
gnuradio-core
usrp2
gr-usrp2
gr-msdd6000
gr-audio
gr-atsc
gr-cvsd-vocoder
gr-gsm-fr-vocoder
gr-noaa
gr-pager
gr-radio-astronomy
gr-trellis
gr-video-sdl
gr-wxgui
gr-qtgui
gnuradio-examples
grc
docs
You my now run the make command to build these components.
*********************************************************************
The
following components were skipped either because you asked not
to build
them or they didn't pass configuration checks:
gcell
usrp
gr-usrp
gr-gcell
gr-comedi
gr-gpio
gr-radar-mono
gr-sounder
gr-utils
gr-uhd
These components will not be built.
Configured GNU Radio release v3.4.0git-139-gf53fef3d for build.
Patrik
_______________________________________________
Discuss-gnuradio
mailing
list
address@hidden
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio