[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Qemu-riscv] [Qemu-devel] [RFC v1 16/23] riscv: tcg-target: Add slow
From: |
Richard Henderson |
Subject: |
Re: [Qemu-riscv] [Qemu-devel] [RFC v1 16/23] riscv: tcg-target: Add slowpath load and store instructions |
Date: |
Fri, 16 Nov 2018 10:24:45 +0100 |
User-agent: |
Mozilla/5.0 (X11; Linux x86_64; rv:60.0) Gecko/20100101 Thunderbird/60.3.0 |
On 11/15/18 11:36 PM, Alistair Francis wrote:
> +static void tcg_out_mb(TCGContext *s, TCGArg a0)
> +{
> + static const RISCVInsn fence[] = {
> + [0 ... TCG_MO_ALL] = OPC_FENCE_RW_RW,
> + [TCG_MO_LD_LD] = OPC_FENCE_R_R,
> + [TCG_MO_ST_LD] = OPC_FENCE_W_R,
> + [TCG_MO_LD_ST] = OPC_FENCE_R_W,
> + [TCG_MO_ST_ST] = OPC_FENCE_W_W,
> + [TCG_BAR_LDAQ] = OPC_FENCE_R_RW,
> + [TCG_BAR_STRL] = OPC_FENCE_RW_W,
> + [TCG_BAR_SC] = OPC_FENCE_RW_RW,
> + };
> + tcg_out32(s, fence[a0 & TCG_MO_ALL]);
> +}
> +
TCG_MO_* and TCG_BAR_* are two different bitmasks, or'ed together.
Which you've separated by "& TCG_MO_ALL". Thus the TCG_BAR_* constants should
not appear in this table.
> +static void * const qemu_ld_helpers[16] = {
> + [MO_UB] = helper_ret_ldub_mmu,
> + [MO_SB] = helper_ret_ldsb_mmu,
> + [MO_LEUW] = helper_le_lduw_mmu,
> + [MO_LESW] = helper_le_ldsw_mmu,
> + [MO_LEUL] = helper_le_ldul_mmu,
> + [MO_LESL] = helper_le_ldsl_mmu,
> + [MO_LEQ] = helper_le_ldq_mmu,
> + [MO_BEUW] = helper_be_lduw_mmu,
> + [MO_BESW] = helper_be_ldsw_mmu,
> + [MO_BEUL] = helper_be_ldul_mmu,
> + [MO_BESL] = helper_be_ldsl_mmu,
> + [MO_BEQ] = helper_be_ldq_mmu,
> +};
The LESL and BESL functions will not be present for rv32 -> link error. Here
you do need an ifdef.
> + } else {
> + adj = cmp_off - sextract32(cmp_off, 0, 12);
> + tcg_debug_assert(add_off - adj >= -0x1000
> + && add_off - adj < 0x1000);
> +
> + tcg_out_opc_upper(s, OPC_LUI, base, adj);
> + tcg_out_opc_reg(s, OPC_ADD, base, TCG_REG_ZERO, TCG_AREG0);
base, base, TCG_AREG0.
> + /* Compare masked address with the TLB entry. */
> + label_ptr[0] = s->code_ptr;
> + tcg_out_opc_branch(s, OPC_BNE, TCG_REG_TMP0, TCG_REG_TMP1, 0);
Another case of a potential out-of-range branch.
It might be worthwhile to move all of this out-of-line from the start, where
that branch will always be short. See
http://lists.nongnu.org/archive/html/qemu-devel/2018-11/msg02234.html
r~
- [Qemu-riscv] [RFC v1 13/23] riscv: tcg-target: Add the extract instructions, (continued)
[Qemu-riscv] [RFC v1 16/23] riscv: tcg-target: Add slowpath load and store instructions, Alistair Francis, 2018/11/15
- Re: [Qemu-riscv] [Qemu-devel] [RFC v1 16/23] riscv: tcg-target: Add slowpath load and store instructions,
Richard Henderson <=
[Qemu-riscv] [RFC v1 17/23] riscv: tcg-target: Add direct load and store instructions, Alistair Francis, 2018/11/15
[Qemu-riscv] [RFC v1 18/23] riscv: tcg-target: Add the out op decoder, Alistair Francis, 2018/11/15
[Qemu-riscv] [RFC v1 19/23] riscv: tcg-target: Add the prologue generation, Alistair Francis, 2018/11/15