|
| From: | Johan Cockx |
| Subject: | Re: [Ltib] Linux Mint 1.6: Can't get: rpm-4.0.4.tar.gz at ./ltib line 834 |
| Date: | Thu, 11 Oct 2012 14:49:06 +0200 |
Hi Johan,
Unfortunately the actual names of the packages vary across distros, so I can't only warn about the generic package name. People will have to figure out what that actually means on their favourite distro.
I'm not sure what your git package fail is. Try removing it completely from /opt/ltib/usr/src/rpm/BUILD/ and re-try. If that fails you need to look at why the directory bld is empty or unreadable (as seen in your output):BTW: please feel free to send patches to improve the project. You may be the first on Mint (I've never tried).
(cd blt && tar cf - .) |
Regards, Stuart
On 10/10/12 13:36, Johan Cockx wrote:Hi Stuart,
Thanks for your reply. I'm a few steps further now, but ltib is not working yet. See below.
The wget command works, and produces exactly the expected output, so network connectivity seems fine. Also, I know I am not behing a proxy.
Anyway, I have installed libwww-perl and the initial messages have disappeared. Also, the rpm-4.0.4.tar.gz error has disappeared.
The next error was that the 'flex' command was not found, so I have done `sudo apt-get install flex' as well, and manually removed /opt/ltib/usr/src/rpm/BUILD/lkc-1.4 before retrying. Shouldn't a check for flex have been included earlier in the ltib script?
Anyway, I tried again, and now I get the following error for the git:
install git '/home/johan/ltib/tmp/git//opt/freescale/rootfs/x86_64/opt/ltib/usr/bin'
make -C templates DESTDIR='/home/johan/ltib/tmp/git//opt/freescale/rootfs/x86_64' install
make[1]: Entering directory `/opt/ltib/usr/src/rpm/BUILD/git-1.5.6.5/templates'
install -d -m 755 '/home/johan/ltib/tmp/git//opt/freescale/rootfs/x86_64/opt/ltib/usr/share/git-core/templates/'
(cd blt && tar cf - .) | \
(cd '/home/johan/ltib/tmp/git//opt/freescale/rootfs/x86_64/opt/ltib/usr/share/git-core/templates/' && umask 022 && tar xf -)
tar: This does not look like a tar archive
tar: Skipping to next header
tar: Exiting with failure status due to previous errors
make[1]: *** [install] Error 2
make[1]: Leaving directory `/opt/ltib/usr/src/rpm/BUILD/git-1.5.6.5/templates'
make: *** [install] Error 2
error: Bad exit status from /home/johan/ltib/tmp/rpm-tmp.53067 (%install)
RPM build errors:
Bad exit status from /home/johan/ltib/tmp/rpm-tmp.53067 (%install)
Build time for git: 43 seconds
Failed building git
Died at ./ltib line 1470.
traceback:
main::build_host_rpms:1470
main::host_checks:1532
main:561
Started: Wed Oct 10 14:28:15 2012
Ended: Wed Oct 10 14:31:39 2012
Elapsed: 204 seconds
VERSION : 11.4.1
CVS_VERSION : $Revision: 1.88 $ (Savannah)
PLATFORM : host
GNUTARCH : x86_64
TOOLCHAIN :
TOOLCHAIN_CFLAGS :
These packages failed to build:
git
Build Failed
As a side note, ltib initially complained about a number of missing packages, including ncurses-devel and zlib-devel. However, 'apt-get install ncurses-devel' and 'apt-get install zlib-devel' cannot find these packages (in the default Mint repositories). It took me some time to figure out that libncurses5-dev and zlib1g-dev provide the required functionality. Would it be a good idea to include this information in the ltib output, so that other first-time installers don't loose time?
Regards, Johan
On Wed, Oct 10, 2012 at 11:11 AM, Stuart Hughes <address@hidden> wrote:
Hi Johan,
The warnings mean that ltib can't test whether or not proxies/networking is available.
I suspect from your error: "Can't get: rpm-4.0.4.tar.gz at ./ltib line 834".
you have network connectivity problem.
To check this, on the machine you're running ltib, make sure you can run:
wget -q -O - bitshrine.org/gpp/rpm-4.0.4.tar.gz.md5
It should show: b92c46d5add17d6edff235d776cc1af3 rpm-4.0.4.tar.gz
If that doesn't work you don't have Internet access. That means you may need to configure the .ltibrc if you're behind a proxy.
Ideally you should install the missing HTTP::Request::Common and LWP::UserAgent Perl modules, these should be in libwww-perl, so: sudo apt-get install libwww-perl
Regards, Stuart
On 10/10/12 09:54, Johan Cockx wrote:_______________________________________________ LTIB home page: http://ltib.org Ltib mailing list address@hidden https://lists.nongnu.org/mailman/listinfo/ltibHi,
I'm trying to install ltib on Linux Mint 1.6, but no succes: the error is "Can't get: rpm-4.0.4.tar.gz at ./ltib line 834".
This is the first time that I am trying to use LTIB. I did the following:
cvs -z3 -d:pserver:address@hidden:/sources/ltib co -P ltib
cd ltib
./ltib
Output is:
Don't have HTTP::Request::Common
Don't have LWP::UserAgent
Cannot test proxies, or remote file availability without both
HTTP::Request::Common and LWP::UserAgent
Installing host support packages.
This only needs to be done once per host, but may take up to
an hour to complete ...
If an error occurs, a log file with the full output may be found in:
/home/johan/ltib/host_config.log
If you would like to see the log messages as the host packages are built and
installed:
* Open another terminal in the same directory
* Run the command: tail -f host_config.log
* When you're done with the tail, use CTRL+C to exit
Exiting on error or interrupt
Please see >> /home/johan/ltib/host_config.log for details
I don't understand the first four lines (about HTTP and LWP); is this related?
Here are the contents of host_config.log:
Processing platform: host support
===================================
Processing: rpm-fs
====================
Build path taken because: no prebuilt rpm,
Can't get: rpm-4.0.4.tar.gz at ./ltib line 834.
Died at ./ltib line 2537.
traceback:
main::check_rpm_setup:2537
main::host_checks:1520
main:561
Started: Wed Oct 10 10:38:14 2012
Ended: Wed Oct 10 10:38:14 2012
Elapsed: 0 seconds
VERSION : 11.4.1
CVS_VERSION : $Revision: 1.88 $ (Savannah)
PLATFORM : host
GNUTARCH : x86_64
TOOLCHAIN :
TOOLCHAIN_CFLAGS :
These packages failed to build:
rpm-fs
Build Failed
Regards,
Johan Cockx
| [Prev in Thread] | Current Thread | [Next in Thread] |