[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Discuss-gnuradio] UHD Announcement - July 6th 2010
From: |
Zohair |
Subject: |
Re: [Discuss-gnuradio] UHD Announcement - July 6th 2010 |
Date: |
Thu, 8 Jul 2010 05:57:51 -0700 (PDT) |
Regarding my post below, I have traced back the error and came to a result
that the error is occurring in device.cpp file. This line in the catch block
throws an error:
device::sptr dev = maker(dev_addr);
I beleive there is something wrong in : Arg: addr=192.168.10.11
192.168.20.11 192.168.30.11 192.168.40.11, recv_buff_size=50e6 50e6 50e6
50e6
Does the block support multiple buffer resizing? or maybe I'm not
addressing the devices properly.
Looking foward to your reply.
Zohair
Zohair wrote:
>
> Dear Josh,
> I have successfully installed the UHD branch from jblum.git repo and have
> tried out using the MIMO sources available. I have a few points to raise
> here regarding this release and block:
>
> 1- I am using a PC with four Ethernet ports. I burned the firmware and the
> fpga images created on 6-7-2010. Also, I tried assigning IP addresses from
> the same subnetwork: 192.168.10.X/24. However, Only a single USRP2 is
> discovered at a time while others are unreachable. (USRP2s IPs are also
> from the same subnetwork above)
>
> 2- Then I tried assigning IPs from 4 different subnetworks to the USRP2's,
> and all them can be discovered normally. Is it possible that they work
> using IPs from the same subnetwork or not? (case 1)
>
> 3- I used a MIMO source with 4 outputs and the following settings:
> freq: 2414000000, 2414000000, 2414000000, 2414000000
> Arg: addr=192.168.10.11 192.168.20.11 192.168.30.11 192.168.40.11,
> recv_buff_size=50e6 50e6 50e6 50e6
> sample rate: 195.312K ( Firstly, I used 32K but at runtime I was prompted
> to use this value)
> Gain= 35,35,35,35
> Antennas= [‘RX2’, ‘RX2’, ‘RX2’, ‘RX2’]
>
> I connected the 4 outputs to graphic scopes but once I run the flowgraph,
> I see this error messages:
>
> terminate called after throwing an instance of
> 'boost::exception_detail::clone_impl<boost::exception_detail::error_info_injector<boost::bad_lexical_cast>
> >'
> what(): bad lexical cast: source type value could not be interpreted as
> target.
>
> I have Boost 1.38.0 installed and I did use this command for
> configuration: ./configure --with-boost=$BOOST_PREFIX
>
> Any advice or help regarding this issue, please?
>
> Best regards,
>
> Zohair
>
--
View this message in context:
http://old.nabble.com/UHD-Announcement---July-6th-2010-tp29091756p29106668.html
Sent from the GnuRadio mailing list archive at Nabble.com.
- [Discuss-gnuradio] UHD Announcement - July 6th 2010, Josh Blum, 2010/07/06
- RE: [Discuss-gnuradio] UHD Announcement - July 6th 2010, Zohair M. Abu-Shaban, 2010/07/09
- Re: [Discuss-gnuradio] UHD Announcement - July 6th 2010, Josh Blum, 2010/07/09
- RE: [Discuss-gnuradio] UHD Announcement - July 6th 2010, Zohair M. Abu Shaban, 2010/07/12
- Re: [Discuss-gnuradio] UHD Announcement - July 6th 2010, Josh Blum, 2010/07/12
- Re: [Discuss-gnuradio] UHD Announcement - July 6th 2010, Zohair, 2010/07/21
- Re: [Discuss-gnuradio] UHD Announcement - July 6th 2010, Josh Blum, 2010/07/21
- Re: [Discuss-gnuradio] UHD Announcement - July 6th 2010, Zohair, 2010/07/26
- Re: [Discuss-gnuradio] UHD Announcement - July 6th 2010, Zohair, 2010/07/26
- Re: [Discuss-gnuradio] UHD Announcement - July 6th 2010, Josh Blum, 2010/07/27