Re: [Qemu-discuss] How to trigger software interrupt on Versatile Express ?

[Mirela Simonović]

2012/4/12 Mirela Simonović <address@hidden>

Hi,

I'm having troubles with triggering a software interrupt on Versatile Express board (Cortex-A9).

I managed to set an interrupt pending, but jump to Vector Table does not execute.

Here is simple program that I'm running:

// ======================================================================================

// File: test.c

// ======================================================================================

#define HAL_READ_UINT32(register, value)  (( value ) = *((volatile unsigned int *)( register )))

#define HAL_WRITE_UINT32(register, value) (*((volatile unsigned int *)( register )) = ( value ))

#define PERIPHBASE 0x1e000000

#define CPUBASE ( PERIPHBASE + 0x100 ) // CPU Interface Base Address

#define DISTBASE   ( PERIPHBASE + 0x1000 )        // Distributor Base Address

#define ICCICR     0x00       // CPU Interface Control Register (RW)

#define ICCPMR   0x04       //

 CPU Interface

 Priority Mask Register (RW)

#define ICDDCR   0x000 // Distributor Control Register (RW)

#define ICDISER  0x100 // 

Distributor 

Interrupt Set Enable Registers (RW) 

#define ICDISPR  0x200 // 

Distributor 

Set Pending Register (RW)

#define ICDIPR    0x400 // 

Distributor 

Interrupt Priority Register (RW)

#define ICDSGIR  0xF00 // 

Distributor 

Software Generated Interrupt Register (WO)

int main ()

{

unsigned int tmp;

HAL_WRITE_UINT32( CPUBASE  + ICCICR, 0 );          // Disable CPU Interface (it is already disabled, but nevermind)

HAL_WRITE_UINT32( DISTBASE + ICDDCR, 0 ); // Disable Distributor (it is already disabled, but nevermind)

HAL_WRITE_UINT32( DISTBASE + ICDISER, 0x0000ffff ); // Set enable (enable all SGIs) 

HAL_WRITE_UINT32( CPUBASE  + ICCPMR, 0xff ); // All interrupts whose priority is > 0xff are unmasked

HAL_WRITE_UINT32( DISTBASE + ICDIPR, 0 ); // Set the highest priority

HAL_WRITE_UINT32( DISTBASE + ICDDCR, 1 ); // Enable Distributor

HAL_WRITE_UINT32( CPUBASE  + ICCICR, 1 ); // Enable CPU Interface

HAL_READ_UINT32 ( DISTBASE + ICDISPR, tmp); // Is the interrupt pending? => No, it's not

HAL_WRITE_UINT32( DISTBASE + ICDSGIR, 0x02000000); // Generate software interrupt ID=0 to CPU0 (to this, running CPU)

HAL_READ_UINT32 ( DISTBASE + ICDISPR, tmp); // Is the interrupt pending? => Yes, it is

return 0;

}

// ======================================================================================

// File: startup.s

// ======================================================================================

.section INTERRUPT_VECTOR, "x"

.global _Reset

_Reset:

  B Reset_Handler /* Reset */

  B . /* Undefined */

  B . /* SWI */

  B . /* Prefetch Abort */

  B . /* Data Abort */

  B . /* reserved */

  B . /* IRQ */

  B . /* FIQ */

Reset_Handler:

  LDR sp, =stack_top

  BL main

  B .

// ======================================================================================

// File: test.ld

// ======================================================================================

ENTRY(_Reset)

SECTIONS

{

. = 0x0;

.text : { startup.o(INTERRUPT_VECTOR)

 *(.text) }

.data : { *(.data) }

.bss : { *(.bss) }

. = . + 0x10000; /* 4 kB for stack */

stack_top = .;

}

// ======================================================================================

Files are compiled and linked with the following:

$ arm-none-eabi-gcc -c -mcpu=cortex-a9 -g test.c -o test.o

$ arm-none-eabi-as -mcpu=cortex-a9 -g startup.s -o startup.o

$ arm-none-eabi-ld -T test.ld test.o startup.o -o test

And I run Qemu with:

$ qemu-system-arm -M vexpress-a9 -m 1024 -kernel test -serial stdio -s -S

In another terminal I attach GDB with:

$ arm-none-eabi-gdb test

(gdb) target remote : 1234

From GDB I can see that all the time CPU is in SVC mode (default after reset) and in CSPR register I flag is 0 (interrupt enabled).

CSPR register I flag is not 0. Before interrupt is generated CPSIE i should be added.

Cheers,

Mirela

 

By reading Set Pending Register at the end of the main function I can see that interrupt is pending, but it not caused jump.

Vector table is placed at the address 0x0, but even if that is not correct I expected a jump.

Please, can anyone take a look what am I missing in the configuration of the GIC?

Or is problem somewhere else?

Thanks,

Mirela