From: "Maciej S. Szmigiero" <maciej.szmigiero@oracle.com>
This driver is like virtio-balloon on steroids: it allows both changing the
guest memory allocation via ballooning and inserting pieces of extra RAM
into it on demand from a provided memory backend.
One of advantages of these over ACPI-based PC DIMM hotplug is that such
memory can be hotplugged in much smaller granularity because the ACPI DIMM
slot limit does not apply.
In order to enable hot-adding additional memory a new memory backend needs
to be created and provided to the driver via the "memdev" parameter.
This can be achieved by, for example, adding
"-object memory-backend-ram,id=mem1,size=32G" to the QEMU command line and
then instantiating the driver with "memdev=mem1" parameter.
In contrast with ACPI DIMM hotplug where one can only request to unplug a
whole DIMM stick this driver allows removing memory from guest in single
page (4k) units via ballooning.
The actual resizing is done via ballooning interface (for example, via
the "balloon" HMP command)
This includes resizing the guest past its boot size - that is, hot-adding
additional memory in granularity limited only by the guest alignment
requirements.
After a VM reboot the guest is back to its original (boot) size.
In the future, the guest boot memory size might be changed on reboot
instead, taking into account the effective size that VM had before that
reboot (much like Hyper-V does).
For performance reasons, the guest-released memory is tracked in a few
range trees, as a series of (start, count) ranges.
Each time a new page range is inserted into such tree its neighbors are
checked as candidates for possible merging with it.
Besides performance reasons, the Dynamic Memory protocol itself uses page
ranges as the data structure in its messages, so relevant pages need to be
merged into such ranges anyway.
One has to be careful when tracking the guest-released pages, since the
guest can maliciously report returning pages outside its current address
space, which later clash with the address range of newly added memory.
Similarly, the guest can report freeing the same page twice.
The above design results in much better ballooning performance than when
using virtio-balloon with the same guest: 230 GB / minute with this driver
versus 70 GB / minute with virtio-balloon.
During a ballooning operation most of time is spent waiting for the guest
to come up with newly freed page ranges, processing the received ranges on
the host side (in QEMU and KVM) is nearly instantaneous.
The unballoon operation is also pretty much instantaneous:
thanks to the merging of the ballooned out page ranges 200 GB of memory can
be returned to the guest in about 1 second.
With virtio-balloon this operation takes about 2.5 minutes.
These tests were done against a Windows Server 2019 guest running on a
Xeon E5-2699, after dirtying the whole memory inside guest before each
balloon operation.
Using a range tree instead of a bitmap to track the removed memory also
means that the solution scales well with the guest size: even a 1 TB range
takes just a few bytes of such metadata.
Since the required GTree operations aren't present in every Glib version
a check for them was added to "configure" script, together with new
"--enable-hv-balloon" and "--disable-hv-balloon" arguments.
If these GTree operations are missing in the system's Glib version this
driver will be skipped during QEMU build.
An optional "status-report=on" device parameter requests memory status
events from the guest (typically sent every second), which allow the host
to learn both the guest memory available and the guest memory in use
counts.
They are emitted externally as "HV_BALLOON_STATUS_REPORT" QMP events.
The driver is named hv-balloon since the Linux kernel client driver for
the Dynamic Memory Protocol is named as such and to follow the naming
pattern established by the virtio-balloon driver.
The whole protocol runs over Hyper-V VMBus.
The driver was tested against Windows Server 2012 R2, Windows Server 2016
and Windows Server 2019 guests and obeys the guest alignment requirements
reported to the host via DM_CAPABILITIES_REPORT message.
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
---
Kconfig.host | 3 +
configure | 36 +
hw/hyperv/Kconfig | 5 +
hw/hyperv/hv-balloon.c | 2040 ++++++++++++++++++++++++++++++++++++++++
hw/hyperv/meson.build | 1 +
hw/hyperv/trace-events | 16 +
meson.build | 4 +-
qapi/machine.json | 25 +
8 files changed, 2129 insertions(+), 1 deletion(-)
create mode 100644 hw/hyperv/hv-balloon.c
diff --git a/Kconfig.host b/Kconfig.host
index d763d89269..2ee71578f3 100644
--- a/Kconfig.host
+++ b/Kconfig.host
@@ -46,3 +46,6 @@ config FUZZ
config VFIO_USER_SERVER_ALLOWED
bool
imply VFIO_USER_SERVER
+
+config HV_BALLOON_POSSIBLE
+ bool