[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [PATCH 2/2] hw/cxl: Multi-Region CXL Type-3 Devices (Volatile and Pe
From: |
Jonathan Cameron |
Subject: |
Re: [PATCH 2/2] hw/cxl: Multi-Region CXL Type-3 Devices (Volatile and Persistent) |
Date: |
Mon, 20 Feb 2023 11:46:46 +0000 |
On Fri, 17 Feb 2023 06:08:57 -0500
Gregory Price <gregory.price@memverge.com> wrote:
> On Fri, Feb 17, 2023 at 04:16:17PM +0000, Jonathan Cameron via wrote:
> > On Tue, 31 Jan 2023 16:38:47 +0000
> > Jonathan Cameron via <qemu-devel@nongnu.org> wrote:
> >
> > > From: Gregory Price <gourry.memverge@gmail.com>
> > >
> > > This commit enables each CXL Type-3 device to contain one volatile
> > > memory region and one persistent region.
> > >
> > > Two new properties have been added to cxl-type3 device initialization:
> > > [volatile-memdev] and [persistent-memdev]
> > >
> > > The existing [memdev] property has been deprecated and will default the
> > > memory region to a persistent memory region (although a user may assign
> > > the region to a ram or file backed region). It cannot be used in
> > > combination with the new [persistent-memdev] property.
> > >
> > > Partitioning volatile memory from persistent memory is not yet supported.
> > >
> > > Volatile memory is mapped at DPA(0x0), while Persistent memory is mapped
> > > at DPA(vmem->size), per CXL Spec 8.2.9.8.2.0 - Get Partition Info.
> > >
> > > Signed-off-by: Gregory Price <gregory.price@memverge.com>
> > > Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> > >
> > Hi Gregory,
> >
> > I've added support for multiple HDM decoders and hence can now
> > test both volatile and non volatile on same device.
> > It very nearly all works. With one exception which is I couldn't
> > poke the first byte of the non volatile region.
> >
> > I think we have an off by one in a single check.
> >
> > Interestingly it makes no difference when creating an FS on top
> > (which was my standard test) so I only noticed when poking memory
> > addresses directly to sanity check the HDM decoder setup.
> >
> > I'll roll a v2 if no one shouts out that I'm wrong.
> >
> > Note that adding multiple HDM decoders massively increases
> > the number of test cases over what we had before to poke all the
> > corners so I may well be missing stuff. Hopefully can send an RFC
> > of that support out next week.
> >
> > Jonathan
> >
>
> Very cool! Thanks for pushing this over the finishing line.
>
> All my testing so far has been really smooth since getting the TCG issue
> worked out.
>
> > > -MemTxResult cxl_type3_read(PCIDevice *d, hwaddr host_addr, uint64_t
> > > *data,
> > > - unsigned size, MemTxAttrs attrs)
> [...]
> > > + if (vmr) {
> > > + if (*dpa_offset <= int128_get64(vmr->size)) {
> >
> > Off by one I think. <
> >
>
> Yes that makes sense, should be <. Derp derp.
>
> Though I think this may alludes to more off-by-one issues? This says
>
> if (dpa_offset < vmr->size)
>
> but dpa_offset should be (hpa - memory_region_base),
>
> The HPA is used by memory access routing for the whole system to determine
> what device it should access.
>
> If that corner case is being hit, doesn't it imply the higher level code
> is also susceptible to this, and is routing accesses to the wrong device?
I don't think so though I may be missing something.
Say vmr->size = 8
hpa dpa_offset
0 0
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 0
etc
Also the writes are turning up where I expect them to.
Also just noticed that the code is setting Memory_base in the CXL dvsec.
Given we are emulating a device as if it has been freshly powered up
those should not be set - it's the OS or firmware's job to set them up.
Harmless though, so can be a cleanup to follow the main series.
We don't currently handle dvsec range based routing anyway and
I'm not sure we ever will as it is a pain to test without some firmware
or OS code to program them for us.
Note that if you update your kernel to cxl/next it will currently fail
as the Range register emulation is (I think) rather over enthusiastic
and currently decides to emulate the HDM decoders for the QEMU emulated
type 3 devices.
https://lore.kernel.org/linux-cxl/167640366272.935665.1056268838301725481.stgit@dwillia2-xfh.jf.intel.com/T/#m6c025d5c9b27d8360a64079593f6c5adaa408772
Jonathan
>
> ~Gregory