[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Qemu-devel] [PATCH 0/6] target/rx: Improvements to disassembly
From: |
Aleksandar Markovic |
Subject: |
Re: [Qemu-devel] [PATCH 0/6] target/rx: Improvements to disassembly |
Date: |
Mon, 27 May 2019 19:47:40 +0200 |
On May 27, 2019 5:44 PM, "Yoshinori Sato" <address@hidden>
wrote:
>
> On Fri, 24 May 2019 00:07:57 +0900,
> Richard Henderson wrote:
> >
> > Here's a sample of the new output, taken from u-boot.bin:
> >
> > IN:
> > 0xfff8000a: fb 12 00 01 00 00 mov.l #0x00000100, r1
> > 0xfff80010: fb 32 f0 13 00 00 mov.l #0x000013f0, r3
> > 0xfff80016: 43 13 sub r1, r3
> > 0xfff80018: fb 22 00 ea f9 ff mov.l #-398848, r2
> > 0xfff8001e: 7f 8f smovf
> > 0xfff80020: ef 01 mov.l r0, r1
> > 0xfff80022: 05 1e 32 00 bsr.a fff83240
> >
> > IN:
> > 0xfff83240: 72 11 5c fb add #-1188, r1
> > 0xfff83244: 75 21 f0 and #-16, r1
> > 0xfff83247: 02 rts
> >
> > Obviously there are still a few inconsistencies in the
> > format strings used for the immediates, but the format
> > is readable and it is easy to look at the opcode to see
> > how our decode compares to the manual.
> >
>
> Hmm.
> The output of the immediate value should be the same as the output of
objdump.
> I do not think that it is the proper format, but I did that because
> it was useful for comparing the results.
>
We in MIPS also use objdump output as the reference and desired output for
QEMU disassembler (not that we are always succeeding in doing that)
Inventing propriatery QEMU output for some instructions is in my view
counterproductive and confusing.
Sincerely,
Aleksandar
> >
> > r~
> >
> >
> > Richard Henderson (6):
> > target/rx: Disassemble rx_index_addr into a string
> > target/rx: Replace operand with prt_ldmi in disassembler
> > target/rx: Use prt_ldmi for XCHG_mr disassembly
> > target/rx: Emit all disassembly in one prt()
> > target/rx: Collect all bytes during disassembly
> > target/rx: Dump bytes for each insn during disassembly
> >
> > target/rx/disas.c | 366 +++++++++++++++++++++-------------------------
> > 1 file changed, 166 insertions(+), 200 deletions(-)
> >
> > --
> > 2.17.1
> >
>
> --
> Yosinori Sato
>
- Re: [Qemu-devel] [PATCH 2/6] target/rx: Replace operand with prt_ldmi in disassembler, (continued)
- [Qemu-devel] [PATCH 5/6] target/rx: Collect all bytes during disassembly, Richard Henderson, 2019/05/23
- [Qemu-devel] [PATCH 3/6] target/rx: Use prt_ldmi for XCHG_mr disassembly, Richard Henderson, 2019/05/23
- [Qemu-devel] [PATCH 6/6] target/rx: Dump bytes for each insn during disassembly, Richard Henderson, 2019/05/23
- [Qemu-devel] [PATCH 4/6] target/rx: Emit all disassembly in one prt(), Richard Henderson, 2019/05/23
- Re: [Qemu-devel] [PATCH 0/6] target/rx: Improvements to disassembly, Yoshinori Sato, 2019/05/27