[Qemu-devel] [PATCH v2 08/11] hw/intc/armv7m_nvic: Fix byte-to-interrupt number conversions

[Peter Maydell]

In many of the NVIC registers relating to interrupts, we
have to convert from a byte offset within a register set
into the number of the first interrupt which is affected.
We were getting this wrong for:
 * reads of NVIC_ISPR<n>, NVIC_ISER<n>, NVIC_ICPR<n>, NVIC_ICER<n>,
   NVIC_IABR<n> -- in all these cases we were missing the "* 8"
   needed to convert from the byte offset to the interrupt number
   (since all these registers use one bit per interrupt)
 * writes of NVIC_IPR<n> had the opposite problem of a spurious
   "* 8" (since these registers use one byte per interrupt)

Signed-off-by: Peter Maydell <address@hidden>
Reviewed-by: Philippe Mathieu-Daudé <address@hidden>
---
 hw/intc/armv7m_nvic.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c
index ea3b7cce14..c51151fa8a 100644
--- a/hw/intc/armv7m_nvic.c
+++ b/hw/intc/armv7m_nvic.c
@@ -1724,7 +1724,7 @@ static MemTxResult nvic_sysreg_read(void *opaque, hwaddr 
addr,
         /* fall through */
     case 0x180 ... 0x1bf: /* NVIC Clear enable */
         val = 0;
-        startvec = offset - 0x180 + NVIC_FIRST_IRQ; /* vector # */
+        startvec = 8 * (offset - 0x180) + NVIC_FIRST_IRQ; /* vector # */
 
         for (i = 0, end = size * 8; i < end && startvec + i < s->num_irq; i++) 
{
             if (s->vectors[startvec + i].enabled &&
@@ -1738,7 +1738,7 @@ static MemTxResult nvic_sysreg_read(void *opaque, hwaddr 
addr,
         /* fall through */
     case 0x280 ... 0x2bf: /* NVIC Clear pend */
         val = 0;
-        startvec = offset - 0x280 + NVIC_FIRST_IRQ; /* vector # */
+        startvec = 8 * (offset - 0x280) + NVIC_FIRST_IRQ; /* vector # */
         for (i = 0, end = size * 8; i < end && startvec + i < s->num_irq; i++) 
{
             if (s->vectors[startvec + i].pending &&
                 (attrs.secure || s->itns[startvec + i])) {
@@ -1748,7 +1748,7 @@ static MemTxResult nvic_sysreg_read(void *opaque, hwaddr 
addr,
         break;
     case 0x300 ... 0x33f: /* NVIC Active */
         val = 0;
-        startvec = offset - 0x300 + NVIC_FIRST_IRQ; /* vector # */
+        startvec = 8 * (offset - 0x300) + NVIC_FIRST_IRQ; /* vector # */
 
         for (i = 0, end = size * 8; i < end && startvec + i < s->num_irq; i++) 
{
             if (s->vectors[startvec + i].active &&
@@ -1863,7 +1863,7 @@ static MemTxResult nvic_sysreg_write(void *opaque, hwaddr 
addr,
     case 0x300 ... 0x33f: /* NVIC Active */
         return MEMTX_OK; /* R/O */
     case 0x400 ... 0x5ef: /* NVIC Priority */
-        startvec = 8 * (offset - 0x400) + NVIC_FIRST_IRQ; /* vector # */
+        startvec = (offset - 0x400) + NVIC_FIRST_IRQ; /* vector # */
 
         for (i = 0; i < size && startvec + i < s->num_irq; i++) {
             if (attrs.secure || s->itns[startvec + i]) {
-- 
2.16.1