Re: [Qemu-devel] vhost-net issue: does not survive reboot on ppc64

[Alexey Kardashevskiy]

On 12/26/2013 09:49 PM, Michael S. Tsirkin wrote:
> On Thu, Dec 26, 2013 at 09:13:31PM +1100, Alexey Kardashevskiy wrote:
>> On 12/25/2013 08:52 PM, Michael S. Tsirkin wrote:
>>> On Wed, Dec 25, 2013 at 12:36:12PM +1100, Alexey Kardashevskiy wrote:
>>>> On 12/25/2013 02:43 AM, Michael S. Tsirkin wrote:
>>>>> On Wed, Dec 25, 2013 at 01:15:29AM +1100, Alexey Kardashevskiy wrote:
>>>>>> On 12/24/2013 08:40 PM, Michael S. Tsirkin wrote:
>>>>>>> On Tue, Dec 24, 2013 at 02:09:07PM +1100, Alexey Kardashevskiy wrote:
>>>>>>>> On 12/24/2013 03:24 AM, Michael S. Tsirkin wrote:
>>>>>>>>> On Mon, Dec 23, 2013 at 02:01:13AM +1100, Alexey Kardashevskiy wrote:
>>>>>>>>>> On 12/23/2013 01:46 AM, Alexey Kardashevskiy wrote:
>>>>>>>>>>> On 12/22/2013 09:56 PM, Michael S. Tsirkin wrote:
>>>>>>>>>>>> On Sun, Dec 22, 2013 at 02:01:23AM +1100, Alexey Kardashevskiy 
>>>>>>>>>>>> wrote:
>>>>>>>>>>>>> Hi!
>>>>>>>>>>>>>
>>>>>>>>>>>>> I am having a problem with virtio-net + vhost on POWER7 machine - 
>>>>>>>>>>>>> it does
>>>>>>>>>>>>> not survive reboot of the guest.
>>>>>>>>>>>>>
>>>>>>>>>>>>> Steps to reproduce:
>>>>>>>>>>>>> 1. boot the guest
>>>>>>>>>>>>> 2. configure eth0 and do ping - everything works
>>>>>>>>>>>>> 3. reboot the guest (i.e. type "reboot")
>>>>>>>>>>>>> 4. when it is booted, eth0 can be configured but will not work at 
>>>>>>>>>>>>> all.
>>>>>>>>>>>>>
>>>>>>>>>>>>> The test is:
>>>>>>>>>>>>> ifconfig eth0 172.20.1.2 up
>>>>>>>>>>>>> ping 172.20.1.23
>>>>>>>>>>>>>
>>>>>>>>>>>>> If to run tcpdump on the host's "tap-id3" interface, it shows no 
>>>>>>>>>>>>> trafic
>>>>>>>>>>>>> coming from the guest. If to compare how it works before and 
>>>>>>>>>>>>> after reboot,
>>>>>>>>>>>>> I can see the guest doing an ARP request for 172.20.1.23 and 
>>>>>>>>>>>>> receives the
>>>>>>>>>>>>> response and it does the same after reboot but the answer does 
>>>>>>>>>>>>> not come.
>>>>>>>>>>>>
>>>>>>>>>>>> So you see the arp packet in guest but not in host?
>>>>>>>>>>>
>>>>>>>>>>> Yes.
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>> One thing to try is to boot debug kernel - where pr_debug is
>>>>>>>>>>>> enabled - then you might see some errors in the kernel log.
>>>>>>>>>>>
>>>>>>>>>>> Tried and added lot more debug printk myself, not clear at all what 
>>>>>>>>>>> is
>>>>>>>>>>> happening there.
>>>>>>>>>>>
>>>>>>>>>>> One more hint - if I boot the guest and the guest does not bring 
>>>>>>>>>>> eth0 up
>>>>>>>>>>> AND wait more than 200 seconds (and less than 210 seconds), then 
>>>>>>>>>>> eth0 will
>>>>>>>>>>> not work at all. I.e. this script produces not-working-eth0:
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> ifconfig eth0 172.20.1.2 down
>>>>>>>>>>> sleep 210
>>>>>>>>>>> ifconfig eth0 172.20.1.2 up
>>>>>>>>>>> ping 172.20.1.23
>>>>>>>>>>>
>>>>>>>>>>> s/210/200/ - and it starts working. No reboot is required to 
>>>>>>>>>>> reproduce.
>>>>>>>>>>>
>>>>>>>>>>> No "vhost" == always works. The only difference I can see here is 
>>>>>>>>>>> vhost's
>>>>>>>>>>> thread which may get suspended if not used for a while after the 
>>>>>>>>>>> start and
>>>>>>>>>>> does not wake up but this is almost a blind guess.
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> Yet another clue - this host kernel patch seems to help with the 
>>>>>>>>>> guest
>>>>>>>>>> reboot but does not help with the initial 210 seconds delay:
>>>>>>>>>>
>>>>>>>>>> diff --git a/drivers/vhost/vhost.c b/drivers/vhost/vhost.c
>>>>>>>>>> index 69068e0..5e67650 100644
>>>>>>>>>> --- a/drivers/vhost/vhost.c
>>>>>>>>>> +++ b/drivers/vhost/vhost.c
>>>>>>>>>> @@ -162,10 +162,10 @@ void vhost_work_queue(struct vhost_dev *dev, 
>>>>>>>>>> struct
>>>>>>>>>> vhost_work *work)
>>>>>>>>>>                 list_add_tail(&work->node, &dev->work_list);
>>>>>>>>>>                 work->queue_seq++;
>>>>>>>>>>                 spin_unlock_irqrestore(&dev->work_lock, flags);
>>>>>>>>>> -               wake_up_process(dev->worker);
>>>>>>>>>>         } else {
>>>>>>>>>>                 spin_unlock_irqrestore(&dev->work_lock, flags);
>>>>>>>>>>         }
>>>>>>>>>> +       wake_up_process(dev->worker);
>>>>>>>>>>  }
>>>>>>>>>>  EXPORT_SYMBOL_GPL(vhost_work_queue);
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>
>>>>>>>>> Interesting. Some kind of race? A missing memory barrier somewhere?
>>>>>>>>
>>>>>>>> I do not see how. I boot the guest and just wait 210 seconds, nothing
>>>>>>>> happens to cause races.
>>>>>>>>
>>>>>>>>
>>>>>>>>> Since it's all around startup,
>>>>>>>>> you can try kicking the host eventfd in
>>>>>>>>> vhost_net_start.
>>>>>>>>
>>>>>>>>
>>>>>>>> How exactly? This did not help. Thanks.
>>>>>>>>
>>>>>>>> diff --git a/hw/net/vhost_net.c b/hw/net/vhost_net.c
>>>>>>>> index 006576d..407ecf2 100644
>>>>>>>> --- a/hw/net/vhost_net.c
>>>>>>>> +++ b/hw/net/vhost_net.c
>>>>>>>> @@ -229,6 +229,17 @@ int vhost_net_start(VirtIODevice *dev, 
>>>>>>>> NetClientState
>>>>>>>> *ncs,
>>>>>>>>          if (r < 0) {
>>>>>>>>              goto err;
>>>>>>>>          }
>>>>>>>> +
>>>>>>>> +        VHostNetState *vn = tap_get_vhost_net(ncs[i].peer);
>>>>>>>> +        struct vhost_vring_file file = {
>>>>>>>> +            .index = i
>>>>>>>> +        };
>>>>>>>> +        file.fd =
>>>>>>>> event_notifier_get_fd(virtio_queue_get_host_notifier(dev->vq));
>>>>>>>> +        r = ioctl(vn->dev.control, VHOST_SET_VRING_KICK, &file);
>>>>>>>
>>>>>>> No, this sets the notifier, it does not kick.
>>>>>>> To kick you write 1 there:
>>>>>>>         uint6_t  v = 1;
>>>>>>>         write(fd, &v, sizeof v);
>>>>>>
>>>>>>
>>>>>> Please, be precise. How/where do I get that @fd? Is what I do correct?
>>>>>
>>>>> Yes.
>>>>>
>>>>>> What
>>>>>> is uint6_t - uint8_t or uint16_t (neither works)?
>>>>>
>>>>> Sorry, should have been uint64_t.
>>>>
>>>>
>>>> Oh, that I missed :-) Anyway, this does not make any difference. Is there
>>>> any cheap&dirty way to make vhost-net kernel thread always awake? Sending
>>>> it signals from the user space does not work...
>>>
>>> You can run a timer in qemu and signal the eventfd from there
>>> periodically.
>>>
>>> Just to restate, tcpdump in guest shows that guest sends arp packet,
>>> but tcpdump in host on tun device does not show any packets?
>>
>>
>> Ok. Figured it out about disabling interfaces in Fedora19. I was wrong,
>> something is happening on the host's TAP - the guest sends ARP request, the
>> response is visible on the TAP interface but not in the guest.
> 
> Okay. So problem is on host to guest path then.
> Things to try:
> 
> 1. trace handle_rx [vhost_net]
> 2. trace tun_put_user [tun]
> 3. I suspect some host bug in one of the features.
> Let's try to disable some flags with device property:
> you can get the list by doing:
> ./x86_64-softmmu/qemu-system-x86_64 -device virtio-net-pci,?|grep on/off
> Things I would try turning off is guest offloads (ones that start with guest_)
> event_idx,any_layout,mq.
> Turn them all off, if it helps try to find the one that helped.


Heh. It still would be awesome to read basics about this vhost thing as I
am debugging blindly :)

Regarding your suggestions.

1. I put "printk" in handle_rx and tun_put_user.
handle_rx stopped being called after 2:40 from the guest start,
tun_put_user stopped after 0:20 from the guest start. Accuracy is 5 seconds.
If I bring the guest's eth0 up while handle_rx is still printing, it works,
i.e. tun_put_user is called a lot. Once handle_rx stopped, nothing can
bring eth0 back to live.

2. This is exactly how I run QEMU now. I basically set "off" for every
on/off parameters. This did not change anything.

./qemu-system-ppc64 \
        -enable-kvm \
        -m 2048 \
        -L qemu-ppc64-bios/ \
        -machine pseries \
        -trace events=qemu_trace_events \
        -kernel vml312 \
        -append root=/dev/sda3 virtimg/fc19_16GB_vhostdbg.qcow2 \
        -nographic \
        -vga none \
        -nodefaults \
        -chardev stdio,id=id0,signal=off,mux=on \
        -device spapr-vty,id=id1,chardev=id0,reg=0x71000100 \
        -mon id=id2,chardev=id0,mode=readline \
        -netdev
tap,id=id3,ifname=tap-id3,script=ifup.sh,downscript=ifdown.sh,vhost=on \
        -device
virtio-net-pci,id=id4,netdev=id3,mac=C0:41:49:4b:00:00,tx=timer,ioeventfd=off,\
indirect_desc=off,event_idx=off,any_layout=off,csum=off,guest_csum=off,\
gso=off,guest_tso4=off,guest_tso6=off,guest_ecn=off,guest_ufo=off,\
host_tso4=off,host_tso6=off,host_ecn=off,host_ufo=off,mrg_rxbuf=off,\
status=off,ctrl_vq=off,ctrl_rx=off,ctrl_vlan=off,ctrl_rx_extra=off,\
ctrl_mac_addr=off,ctrl_guest_offloads=off,mq=off,multifunction=off,\
command_serr_enable=off \
        -netdev user,id=id5,hostfwd=tcp::5000-:22 \
        -device spapr-vlan,id=id6,netdev=id5,mac=C0:41:49:4b:00:01



-- 
Alexey