[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Paparazzi-devel] PPM Encoder and Lisa/L
From: |
Felix Ruess |
Subject: |
Re: [Paparazzi-devel] PPM Encoder and Lisa/L |
Date: |
Fri, 18 Nov 2011 10:13:42 +0100 |
But since the 8 channel PPM encoder actually always outputs 8
channels, you have to define 8 channels in your radio.xml file like in
the example on the wiki.
Cheers, Felix
On Fri, Nov 18, 2011 at 10:03 AM, Jochen Rieger <address@hidden> wrote:
> In the radio file is also just configure 6 channels(6 channel receiver). I
> wanted just say that is the 8 channel PPM encoder from Hendrix.
>
> -Jochen
>
> 2011/11/18 Christophe De Wagter <address@hidden>
>>
>> You have 6 zero's in the rc-message view, while the encoder sends 8
>> channels? That sounds like a radio.xml not being compatible with the number
>> of pulses?
>> Note that paparazzi PPM reading is very selective. This dates from the
>> time where everyone was using 35MHz. If 2 transmitters were on the same
>> frequency, you wanted to be sure that paparazzi would not accept this
>> corrupted signal.
>>
>> -Christophe
>>
>>
>>
>> On Fri, Nov 18, 2011 at 8:33 AM, Jochen Rieger <address@hidden>
>> wrote:
>>>
>>> Hello,
>>>
>>> i have a problem with the PPM at Lisa/L. I can see an signal at PPM
>>> output of the 8 Channel PPM Encoder Version 2, that seems to be a PPM
>>> signal(measured with scope). The input port of the PPM signal is the Trig.
>>> port of UART1 at Lisa/L (pin 1).
>>> But when I set the tele_FBW to 1 in GCS. I see only 0,0,0,0,0,0 in the
>>> value message window.
>>>
>>> I have setup the radio file like the wiki. The right pulse_type and the
>>> right numbers of input channelns.
>>> Have anyone an idea?
>>>
>>> Best regards.
>>> Jochen
>>>
>>> _______________________________________________
>>> Paparazzi-devel mailing list
>>> address@hidden
>>> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>>>
>>
>>
>> _______________________________________________
>> Paparazzi-devel mailing list
>> address@hidden
>> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>>
>
>
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden
> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>
>
- [Paparazzi-devel] PPM Encoder and Lisa/L, Jochen Rieger, 2011/11/18
- Re: [Paparazzi-devel] PPM Encoder and Lisa/L, Christophe De Wagter, 2011/11/18
- Re: [Paparazzi-devel] PPM Encoder and Lisa/L, Jochen Rieger, 2011/11/18
- Re: [Paparazzi-devel] PPM Encoder and Lisa/L,
Felix Ruess <=
- Re: [Paparazzi-devel] PPM Encoder and Lisa/L, Christophe De Wagter, 2011/11/18
- Re: [Paparazzi-devel] PPM Encoder and Lisa/L, Jochen Rieger, 2011/11/18
- Re: [Paparazzi-devel] PPM Encoder and Lisa/L, Felix Ruess, 2011/11/18
- Re: [Paparazzi-devel] PPM Encoder and Lisa/L, Jochen Rieger, 2011/11/18
- Re: [Paparazzi-devel] PPM Encoder and Lisa/L, Chris Gough, 2011/11/18
- Re: [Paparazzi-devel] PPM Encoder and Lisa/L, Jochen Rieger, 2011/11/18
- Re: [Paparazzi-devel] PPM Encoder and Lisa/L, Felix Ruess, 2011/11/18
- Re: [Paparazzi-devel] PPM Encoder and Lisa/L, Jochen Rieger, 2011/11/18
- Re: [Paparazzi-devel] PPM Encoder and Lisa/L, Felix Ruess, 2011/11/18
- Re: [Paparazzi-devel] PPM Encoder and Lisa/L, Jochen Rieger, 2011/11/18