[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
RE: [Freeipmi-users] Resolving error: "could not find inband device"
From: |
Al Chu |
Subject: |
RE: [Freeipmi-users] Resolving error: "could not find inband device" |
Date: |
Sat, 15 Nov 2008 06:54:13 -0500 |
Can you do the full install instead of the just copying the files over.
There's atleast one other file a few of the drivers require that comes
with the full-install.
Al
On Sat, 2008-11-15 at 06:54 -0700, address@hidden wrote:
> Hi Al,
>
> ipmi-locate works. Here is the output.
>
> Probing KCS device using DMIDECODE... done
> IPMI Version: 2.0
> IPMI locate driver: DMIDECODE
> IPMI interface: KCS
> BMC driver device:
> BMC I/O base address: 0xCA2
> Register spacing: 1
>
> Probing SMIC device using DMIDECODE... FAILED
>
> Probing BT device using DMIDECODE... FAILED
>
> Probing SSIF device using DMIDECODE... FAILED
>
> Probing KCS device using SMBIOS... done
> IPMI Version: 2.0
> IPMI locate driver: SMBIOS
> IPMI interface: KCS
> BMC driver device:
> BMC I/O base address: 0xCA2
> Register spacing: 1
>
> Probing SMIC device using SMBIOS... FAILED
>
> Probing BT device using SMBIOS... FAILED
>
> Probing SSIF device using SMBIOS... FAILED
>
> Probing KCS device using ACPI... FAILED
>
> Probing SMIC device using ACPI... FAILED
>
> Probing BT device using ACPI... FAILED
>
> Probing SSIF device using ACPI... FAILED
>
> Probing KCS device using PCI... FAILED
>
> Probing SMIC device using PCI... FAILED
>
> Probing BT device using PCI... FAILED
>
> Probing SSIF device using PCI... FAILED
>
> KCS device default values:
> IPMI Version: 1.5
> IPMI locate driver: DEFAULT
> IPMI interface: KCS
> BMC driver device:
> BMC I/O base address: 0xCA2
> Register spacing: 1
>
> SMIC device default values:
> IPMI Version: 1.5
> IPMI locate driver: DEFAULT
> IPMI interface: SMIC
> BMC driver device:
> BMC I/O base address: 0xCA9
> Register spacing: 1
>
> BT device default values:
> SSIF device default values:
> IPMI Version: 1.5
> IPMI locate driver: DEFAULT
> IPMI interface: SSIF
> BMC driver device: /dev/i2c-0
> BMC SMBUS slave address: 0x42
> Register spacing: 1
>
>
> -------- Original Message --------
> Subject: Re: [Freeipmi-users] Resolving error: "could not find
> inband
> device"
> From: Al Chu <address@hidden>
> Date: Fri, November 14, 2008 11:31 am
> To: address@hidden
> Cc: address@hidden
>
> Hey Michael,
>
> Hmmm. It should work for you just fine. It is possible that
> the IPMI
> card on the other machine is broken and thus nothing can be
> found. Does
> ipmi-locate give you different results on the two machines?
>
> Al
>
> On Fri, 2008-11-14 at 10:41 -0500, address@hidden wrote:
> > Hi,
> >
> > I compiled and ran ipmi-sensors successfully, but when i
> tried to run it on
> > a different machine after copying just the /usr/sbin and
> usr/lib64 files
> > generated by the previous compile, i get this error on the
> machine where I
> > just copied the binaries:
> >
> > ipmi-sensors
> > could not find inband device
> >
> > Anybody know what else needs to loaded on the other computer
> that these
> > binaries need? The other machine is a clone of the machine I
> ran the
> > compile on: same hardware/software.
> >
> > Respectfully Yours,
> > Michael Vitale
> >
> >
> <mailto:address@hidden>
> > address@hidden
> > 703-663-3770
> >
> > 703=600-9343
> >
> >
> > _______________________________________________
> > Freeipmi-users mailing list
> > address@hidden
> > http:// lists.gnu.org/mailman/listinfo/freeipmi-users
> >
> --
> Albert Chu
> address@hidden
> Computer Scientist
> High Performance Systems Division
> Lawrence Livermore National Laboratory
>
>
--
Albert Chu
address@hidden
Computer Scientist
High Performance Systems Division
Lawrence Livermore National Laboratory