Right, because the filter cutoff frequency needs to be at least half the
sampling rate, I figured I would not be able to use a filter since the
bladeRF I will be using has a 61.44 MHz sampling rate and I will be
operating in the GHz range.
What I will probably end up having to do is do a pre-run calibration
where the tone is not playing, use a complex to mag^2 and average power
combination, set that as a constant block, and then subtract the
calibrated constant from the total power when the tone is on to get the
most accurate possible signal power. While not ideal because it is not a
truly live SNR calculation, it is the best workaround that avoids the
filter I can think of.
If there are any other suggestions to get a more live/real time SNR
calculation I am open to that as well.
Thank you for the help,
Alex
On Fri, Jun 26, 2020 at 4:17 AM Johannes Demel <demel@ant.uni-bremen.de
<mailto:demel@ant.uni-bremen.de>> wrote:
Hi Alex,
"0 < fa <= sampling_rate/2" is correct and should always be
enforced. If
you try to set your filter cut-off frequency at >= samp_rate/2, you'll
experience aliasing.
After reading your mails, I get the impression you try to set your
filter cut-off frequency at your carrier frequency $f_c$ + bandwidth/2
$B/2$. Or something in that range. That won't work in baseband.
Effectively, your signal at $f_c$ goes through a mixer and is shifted
such that it would appear at $0$ in your baseband signal.
There's a lot of digital signal processing fundamentals involved. I
like
the explanations given in [0]. Though, of course there are well known
books such as the ones by Proakis or Sklar on the topic.
Cheers
Johannes
[0] https://dspillustrations.com/pages/index.html
On 25.06.20 22:22, Alex Batts wrote:
> The effective noise bandwidth is part of the calculation. I'm
using the
> radar range equation.
>
> My purpose for including the bandwidth in my response was that
any time
> I try to use a filter with a frequency greater than my sampling
rate/2 I
> get an error returned. I agree that ideally I would use a band-pass
> filter with very narrow cutoffs to best capture the signal in its
> entirety, however, I can't because the frequency I'm trying to
set my
> filter at is more than half my sampling rate, giving me an error.
Maybe
> there is something askew with that error and it's something else,
but it
> returns saying 0 < fa <= sampling_rate/2
>
> On Thu, Jun 25, 2020 at 3:27 PM Marcus Müller <mueller@kit.edu
<mailto:mueller@kit.edu>
> <mailto:mueller@kit.edu <mailto:mueller@kit.edu>>> wrote:
>
> Hi Alex,
>
> On 25/06/2020 21.00, Alex Batts wrote:
> > I'm sampling an incoming signal, but only around 2 MSps.
> >
>
> and that's fine! that's the *equivalent* baseband, it has all
the same
> information as the RF signal.
>
> > I need the signal power to noise power ratio at the
receiver as
> part of
> > my range calculation.
>
> Yes, but you'd always want to do that "signal to noise" only
in the
> bandwidth that actually contains your tone; the rest will
just contain
> more noise, interferers... to make your measurement worse.
>
> > So I would need to be able to distinguish between
> > the power of the tone vs the power of the surrounding
noise and use
> > those two numerical values in an equation to calculate the
range.
>
> You need to define "surrounding"! Your signal doesn't get
worse by
> applying a filter that only selects your tone and as little
else as
> possible. So you should do that – it makes your SNR better.
Hence, your
> Signal power estimate gets more reliable (which you
definitely want).
>
> (that also highlights why I have a bit of doubt on your
measurement
> methodology – if your SNR depends on receiver bandwidth, then
how much
> does it actually tell you about the range, unless you specify the
> bandwidth alongside with it?)
>
> Think about it: we typically assume noise to be white, i.e.
to have
> identical power spectral density all over the spectrum, e.g. -170
> dBm/Hz.
>
> Now, if your receiver bandwidth is set to 2 MHz (because
that's what
> your SDR is probably configured to filter out if you ask for
2 MS/s),
> then you get twice as much noise power than if you set the
sampling
> rate
> to 1 MS/s.
>
> It's the same thing that I always let students figure out by
themselves
> the first time they use the lab spectrum analyzer:
> Feed a 2 GHz -60 dBm tone into the spectrum analyzer.
> Set the resolution bandwidth of the spectrum analyzer to 1
MHz, and
> tell
> me what the SNR is. Now set the resolution bandwidth to 300
kHz and
> tell
> me again.
> You get as much "N" in your SNR as you let through your
system. In the
> case of the spectrum analyzer, every point on the display is
the power
> in 1 MHz (or 300 kHz) of filter. In the case of your Qt plot,
it's the
> power in a FFT bin. There's (f_sample)/(FFT length) bandwidth
to each
> bin; so your graphical analysis hinges on the setting of
sample rate
> and
> FFT length (also, on window choice and labeling, and software
> convention). Proportionally!
>
> It's really hard to define "SNR" for 0-bandwidth, i.e. a
single tone
> (having a single tone, actually, gets tricky physically, but
there's a
> lot of people who could tell you more about oscillators than
I could).
>
> If you'd be fair, the only choice for the noise filter
bandwidth would
> be 0 Hz, because if you chose any wider, you always get more
noise. But
> in 0 Hz, there's actually 0 noise power! So, that doesn't work.
>
> Instead, you need to define SNR exactly on the bandwidth your
detection
> system will have to use. That's a design parameter you haven't
> mentioned
> so far!
>
> > This
> > is why I referenced the green and red lines on the qt gui
freq.
> display,
> > this would seem to give me signal strength in dB.
>
> Hopefully, above explained how much these lines depend on your
> configuration and aren't "SNR".
>
> Cheers,
> Marcus
>