[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Discuss-gnuradio] usrper fails in usb_claim_interface
From: |
Eric Blossom |
Subject: |
Re: [Discuss-gnuradio] usrper fails in usb_claim_interface |
Date: |
Tue, 5 Apr 2005 14:18:19 -0700 |
User-agent: |
Mutt/1.5.6i |
On Tue, Apr 05, 2005 at 12:03:00PM -0700, Larry Doolittle wrote:
> Hi -
>
> I have an Avnet Virtex 4 evaluation board, intended for
> projects similar in concept to GNU Radio. It uses the
> same CY7C68013 chip as USRP.
>
> I used USRP as a software reference design, and started
> splicing in some code of my own. I think that part is
> in good shape, after coming up to speed on SDCC etc.
>
> When I go to download my .ihx file, usrper says:
>
> # usrper -x load_firmware ${FOO}/usrp_main.ihx
> lt-usrper: found unconfigured FX2; needs firmware.
> usrp_open_interface:usb_claim_interface: failed interface 0
> could not claim interface 0: Device or resource busy
> lt-usrper: failed to open_cmd_interface
> #
>
> I am running this as root, to avoid possible permissions
> problems. The Linux kernel is 2.6.10-9-amd64-k8, base
> distribution is debian sid.
I suspect that you may have the usbtest module loaded.
If so it grab the FX2 interface.
Try this:
# lsmod
# rmmod usbtest
> The curious thing is that both fxload and fx2_programmer
> seem to work; with fxload, I have even confirmed (by watching
> I/O pins with a scope) that my .ihx file loads and runs.
Not sure about those...
> strace shows a non-surprising:
>
> open("/proc/bus/usb/005/005", O_RDWR) = 3
> ioctl(3, USBDEVFS_SETCONFIGURATION, 0x7fbffffb2c) = 0
> ioctl(3, USBDEVFS_CLAIMINTERFACE, 0x7fbffffb2c) = -1 EBUSY (Device or
> resource busy)
> write(2,
> "usrp_open_interface:usb_claim_in"...,60usrp_open_interface:usb_claim_interface:
> failed interface 0
> ) = 60
>
> I found http://comsec.com/wiki?UsrpInstall, where this message
> is listed, and it says to use USB 2.0 instead of USB 1.1.
> If I read my kernel logs correctly, I _do_ have USB 2.0 active:
>
> 2005-04-05 11:20:16.200324500 <6>usb 5-1: new high speed USB device using
> ehci_hcd and address 6
> 2005-04-05 11:20:16.264596500 <6>usbtest 5-1:1.0: FX2 device
> 2005-04-05 11:20:16.264640500 <6>usbtest 5-1:1.0: high speed {control bulk-in
> bulk-out} tests (+alt)
----------------------------------^^^^^^^
You have the usbtest module loaded.
rmmod it.
> 2005-04-05 11:20:45.881313500 <4>usb 5-1: usbfs: interface 0 claimed while
> 'lt-usrper' sets config #1
> 2005-04-05 11:35:07.626327500 <4>usb 5-1: usbfs: interface 0 claimed while
> 'lt-usrper' sets config #1
>
> Anybody have a clue they can share with me?
>
> - Larry
Eric
- [Discuss-gnuradio] usrper fails in usb_claim_interface, Larry Doolittle, 2005/04/05
- Re: [Discuss-gnuradio] usrper fails in usb_claim_interface, mgray, 2005/04/05
- Re: [Discuss-gnuradio] usrper fails in usb_claim_interface,
Eric Blossom <=
- Re: [Discuss-gnuradio] usrper fails in usb_claim_interface, Larry Doolittle, 2005/04/06
- Re: [Discuss-gnuradio] usrper fails in usb_claim_interface, Matt Ettus, 2005/04/06
- Re: [Discuss-gnuradio] usrper fails in usb_claim_interface, James Cooley, 2005/04/27
- Re: [Discuss-gnuradio] usrper fails in usb_claim_interface, Eric Blossom, 2005/04/27
- Re: [Discuss-gnuradio] usrper fails in usb_claim_interface, James Cooley, 2005/04/27
- Re: [Discuss-gnuradio] usrper fails in usb_claim_interface, Eric Blossom, 2005/04/27
- Re: [Discuss-gnuradio] usrper fails in usb_claim_interface, James Cooley, 2005/04/29
- Re: [Discuss-gnuradio] usrper fails in usb_claim_interface, Eric Blossom, 2005/04/29