|
From: | Lefteris Kampianakis |
Subject: | Re: [Discuss-gnuradio] RuntimeError: b200: 2 RX 1 TX and 1 RX 2 TX configurations not possible |
Date: | Tue, 18 Nov 2014 14:27:51 -0800 |
USRP_source_channel1 --> USRP_sink_channel1Hello,FYI I am having problems even with a simpler configuration like this:
USRP_source_channel2 --> USRP_sink_channel2Does anyone face the same issue? It is really frustrating because 1/3 executions are wasted and this causes problems with later design, that has to have an execution rate of > 1Hz
Thank you in advanceLefteris--On Fri, Nov 14, 2014 at 6:32 PM, Lefteris Kampianakis <address@hidden> wrote:The problem I have is that I get the following message at random times and on average on 1/3 executions of the GRC script.USRP_source_channel1 --> WX_GUI_scope_channel1address@hidden --> USRP_sink_channel1Hello,I have a B210 and I am trying to transmit and receive from all it's channels simultaneously. My setup is a macmini late 2012 with Ubuntu 12.04 install. I compiled and installed gnuradio from source using the gnuradio build script. I have developed the attached very simple GRC script that looks like this
address@hidden --> USRP_sink_channel2
USRP_source_channel2 --> WX_GUI_scope_channel2
linux; GNU C++ version 4.6.3; Boost_104800; UHD_003.008.000-18-g864f84b5
Using Volk machine: avx_64_mmx_orc
-- Operating over USB 3.
-- Initialize CODEC control...
-- Initialize Radio control...
-- Performing register loopback test... pass
-- Performing register loopback test... pass
-- Performing CODEC loopback test... pass
-- Performing CODEC loopback test... pass
-- Asking for clock rate 32.000000 MHz
-- Actually got clock rate 32.000000 MHz
-- Performing timer loopback test... pass
-- Performing timer loopback test... pass
-- Asking for clock rate 28.000000 MHz
-- Actually got clock rate 28.000000 MHz
-- Performing timer loopback test... pass
-- Performing timer loopback test... pass
-- Tune Request: 915.000000 MHz
-- The RF LO does not support the requested frequency:
-- Requested LO Frequency: 915.000000 MHz
-- RF LO Result: 914.999999 MHz
-- Attempted to use the DSP to reach the requested frequency:
-- Desired DSP Frequency: -0.000001 MHz
-- DSP Result: -0.000001 MHz
-- Successfully tuned to 915.000000 MHz
--
-- Tune Request: 915.000000 MHz
-- The RF LO does not support the requested frequency:
-- Requested LO Frequency: 915.000000 MHz
-- RF LO Result: 914.999999 MHz
-- Attempted to use the DSP to reach the requested frequency:
-- Desired DSP Frequency: -0.000001 MHz
-- DSP Result: -0.000001 MHz
-- Successfully tuned to 915.000000 MHz
--
-- Asking for clock rate 28.000000 MHz
-- Actually got clock rate 28.000000 MHz
-- Performing timer loopback test... pass
-- Performing timer loopback test... pass
-- Tune Request: 915.000000 MHz
-- The RF LO does not support the requested frequency:
-- Requested LO Frequency: 915.000000 MHz
-- RF LO Result: 914.999999 MHz
-- Attempted to use the DSP to reach the requested frequency:
-- Desired DSP Frequency: 0.000001 MHz
-- DSP Result: 0.000001 MHz
-- Successfully tuned to 915.000000 MHz
--
-- Tune Request: 915.000000 MHz
-- The RF LO does not support the requested frequency:
-- Requested LO Frequency: 915.000000 MHz
-- RF LO Result: 914.999999 MHz
-- Attempted to use the DSP to reach the requested frequency:
-- Desired DSP Frequency: 0.000001 MHz
-- DSP Result: 0.000001 MHz
-- Successfully tuned to 915.000000 MHz
--
thread[thread-per-block[2]: <block gr uhd usrp sink (24)>]: RuntimeError: b200: 2 RX 1 TX and 1 RX 2 TX configurations not possibleIt is obvious that I have all channels activated and that this message shouldn't be appearing in the first place, let alone, appearing in a non-deterministic manner.Any ideas?Thank you in advanceLefterisEleftherios(Lefteris) KampianakisElectronics and Computer EngineerPHD Candidate and Researcher at Sensing Computing Communications Group (SGCC)Department of Electrical EngineeringUniversity of Washington3927 Adams Lane, NE, Mercer Court D805B, 98105mail: address@hidden
complete.grc
Description: application/gnuradio-grc
simple.grc
Description: application/gnuradio-grc
file_sinks.py
Description: Text Data
lshw_output
Description: Binary data
[Prev in Thread] | Current Thread | [Next in Thread] |