Re: [Discuss-gnuradio] RuntimeError: b200: 2 RX 1 TX and 1 RX 2 TX configurations not possible

[Lefteris Kampianakis]

Hello,

FYI I am having problems even with a simpler configuration like this:

USRP_source_channel1 --> USRP_sink_channel1
USRP_source_channel2 --> USRP_sink_channel2

Does anyone face the same issue? It is really frustrating because 1/3 executions are wasted and this causes problems with later design, that has to have an execution rate of > 1Hz

Thank you in advance

Lefteris

On Fri, Nov 14, 2014 at 6:32 PM, Lefteris Kampianakis <address@hidden> wrote:

Hello,

I have a B210 and I am trying to transmit and receive from all it's channels simultaneously. My setup is a macmini late 2012 with Ubuntu 12.04 install. I compiled and installed gnuradio from source using the gnuradio build script. I have developed the attached very simple GRC script that looks like this

address@hidden --> USRP_sink_channel1
address@hidden --> USRP_sink_channel2

USRP_source_channel1 --> WX_GUI_scope_channel1
USRP_source_channel2 --> WX_GUI_scope_channel2

The problem I have is that I get the following message at random times and on average on 1/3 executions of the GRC script.

linux; GNU C++ version 4.6.3; Boost_104800; UHD_003.008.000-18-g864f84b5

Using Volk machine: avx_64_mmx_orc
-- Operating over USB 3.
-- Initialize CODEC control...
-- Initialize Radio control...
-- Performing register loopback test... pass
-- Performing register loopback test... pass
-- Performing CODEC loopback test... pass
-- Performing CODEC loopback test... pass
-- Asking for clock rate 32.000000 MHz
-- Actually got clock rate 32.000000 MHz
-- Performing timer loopback test... pass
-- Performing timer loopback test... pass
-- Asking for clock rate 28.000000 MHz
-- Actually got clock rate 28.000000 MHz
-- Performing timer loopback test... pass
-- Performing timer loopback test... pass
-- Tune Request: 915.000000 MHz
--   The RF LO does not support the requested frequency:
--     Requested LO Frequency: 915.000000 MHz
--     RF LO Result: 914.999999 MHz
--   Attempted to use the DSP to reach the requested frequency:
--     Desired DSP Frequency: -0.000001 MHz
--     DSP Result: -0.000001 MHz
--   Successfully tuned to 915.000000 MHz
--
-- Tune Request: 915.000000 MHz
--   The RF LO does not support the requested frequency:
--     Requested LO Frequency: 915.000000 MHz
--     RF LO Result: 914.999999 MHz
--   Attempted to use the DSP to reach the requested frequency:
--     Desired DSP Frequency: -0.000001 MHz
--     DSP Result: -0.000001 MHz
--   Successfully tuned to 915.000000 MHz
--
-- Asking for clock rate 28.000000 MHz
-- Actually got clock rate 28.000000 MHz
-- Performing timer loopback test... pass
-- Performing timer loopback test... pass
-- Tune Request: 915.000000 MHz
--   The RF LO does not support the requested frequency:
--     Requested LO Frequency: 915.000000 MHz
--     RF LO Result: 914.999999 MHz
--   Attempted to use the DSP to reach the requested frequency:
--     Desired DSP Frequency: 0.000001 MHz
--     DSP Result: 0.000001 MHz
--   Successfully tuned to 915.000000 MHz
--
-- Tune Request: 915.000000 MHz
--   The RF LO does not support the requested frequency:
--     Requested LO Frequency: 915.000000 MHz
--     RF LO Result: 914.999999 MHz
--   Attempted to use the DSP to reach the requested frequency:
--     Desired DSP Frequency: 0.000001 MHz
--     DSP Result: 0.000001 MHz
--   Successfully tuned to 915.000000 MHz
--
thread[thread-per-block[2]: <block gr uhd usrp sink (24)>]: RuntimeError: b200: 2 RX 1 TX and 1 RX 2 TX configurations not possible

It is obvious that I have all channels activated and that this message shouldn't be appearing in the first place, let alone, appearing in a non-deterministic manner.

Any ideas?

Thank you in advance

Lefteris

--

Eleftherios(Lefteris) Kampianakis

Electronics and Computer Engineer

PHD Candidate and Researcher at Sensing Computing Communications Group (SGCC)

Department of Electrical Engineering

University of Washington

3927 Adams Lane, NE, Mercer Court D805B, 98105

website: http://staff.washington.edu/ekampian/

mail: address@hidden