Re: [RFC PATCH 2/2] arm/virt: Add aspeed-i2c controller and MCTP EP to enable MCTP testing

[Corey Minyard]

On Tue, May 24, 2022 at 05:50:43PM +0100, Jonathan Cameron wrote:
> On Tue, 24 May 2022 09:36:44 -0700
> Ben Widawsky <bwidawsk@kernel.org> wrote:
> 
> > On 22-05-20 18:01:28, Jonathan Cameron wrote:
> > > As the only I2C emulation in QEMU that supports being both
> > > a master and a slave, suitable for MCTP over i2c is aspeed-i2c
> > > add this controller to the arm virt model and hook up our new
> > > i2c_mctp_cxl_fmapi device.
> > > 
> > > The current Linux driver for aspeed-i2c has a hard requirement on
> > > a reset controller.  Throw down the simplest reset controller
> > > I could find so as to avoid need to make any chance to the kernel
> > > code.  
> > 
> > s/chance/change
> oops :)
> > 
> > > 
> > > Patch also builds appropriate device tree.  Unfortunately for CXL
> > > we need to use ACPI (no DT bindings yet defined). Enabling this will
> > > either require appropriate support for MCTP on an i2c master that
> > > has ACPI bindings, or modifications of the kernel driver to support
> > > ACPI with aspeed-i2c (which might be a little controversial ;)  
> > 
> > I'm naive to what DT defines, but I assume what's there already is 
> > insufficient
> > to make the bindings for CXL. I say this because I believe it wouldn't be 
> > too
> > bad at all to make a cxl_dt.ko, and it's certainly less artificial than
> > providing ACPI support for things which don't naturally have ACPI support.
> 
> It wouldn't be that hard to work out a CXL dt binding, but it's not
> of sufficient interest to me that I'd want to do it (I'll review if someone
> else sends patches). Platforms I'm interested in CXL with are all strictly
> ACPI only.
> 
> The trick here I think, is going to be adding ACPI support for a suitable I2C 
> controller
> which supports the requirement for supporting master and and I2C EP needed
> for MCTP. Either I find one that already has ACPI bindings and add enough
> emulation for this functionality, or work around the lack of ACPI bindings 
> for the
> aspeed-i2c controller.
> 
> Based on a really quick check of I2C masters for which I have docs and that
> definitely have ACPI bindings, it's not a particularly common feature set.

Ben already got my comments.

It's not common, but it's something you are using, so it obviously
exists.  What hardware do you have?  The most natural thing might be to
add your controller.

-corey

> 
> Jonathan
> 
> 
> 
> > 
> > > 
> > > Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> > > ---
> > >  hw/arm/Kconfig        |  1 +
> > >  hw/arm/virt.c         | 77 +++++++++++++++++++++++++++++++++++++++++++
> > >  include/hw/arm/virt.h |  2 ++
> > >  3 files changed, 80 insertions(+)
> > > 
> > > diff --git a/hw/arm/Kconfig b/hw/arm/Kconfig
> > > index 219262a8da..4a733298cd 100644
> > > --- a/hw/arm/Kconfig
> > > +++ b/hw/arm/Kconfig
> > > @@ -30,6 +30,7 @@ config ARM_VIRT
> > >      select ACPI_VIOT
> > >      select VIRTIO_MEM_SUPPORTED
> > >      select ACPI_CXL
> > > +    select I2C_MCTP_CXL_FMAPI
> > >  
> > >  config CHEETAH
> > >      bool
> > > diff --git a/hw/arm/virt.c b/hw/arm/virt.c
> > > index d818131b57..ea04279515 100644
> > > --- a/hw/arm/virt.c
> > > +++ b/hw/arm/virt.c
> > > @@ -80,6 +80,9 @@
> > >  #include "hw/char/pl011.h"
> > >  #include "hw/cxl/cxl.h"
> > >  #include "qemu/guest-random.h"
> > > +#include "hw/i2c/i2c.h"
> > > +#include "hw/i2c/aspeed_i2c.h"
> > > +#include "hw/misc/i2c_mctp_cxl_fmapi.h"
> > >  
> > >  #define DEFINE_VIRT_MACHINE_LATEST(major, minor, latest) \
> > >      static void virt_##major##_##minor##_class_init(ObjectClass *oc, \
> > > @@ -156,6 +159,8 @@ static const MemMapEntry base_memmap[] = {
> > >      [VIRT_PVTIME] =             { 0x090a0000, 0x00010000 },
> > >      [VIRT_SECURE_GPIO] =        { 0x090b0000, 0x00001000 },
> > >      [VIRT_MMIO] =               { 0x0a000000, 0x00000200 },
> > > +    [VIRT_I2C] =                { 0x0b000000, 0x00004000 },
> > > +    [VIRT_RESET_FAKE] =         { 0x0b004000, 0x00000010 },
> > >      /* ...repeating for a total of NUM_VIRTIO_TRANSPORTS, each of that 
> > > size */
> > >      [VIRT_PLATFORM_BUS] =       { 0x0c000000, 0x02000000 },
> > >      [VIRT_SECURE_MEM] =         { 0x0e000000, 0x01000000 },
> > > @@ -192,6 +197,7 @@ static const int a15irqmap[] = {
> > >      [VIRT_GPIO] = 7,
> > >      [VIRT_SECURE_UART] = 8,
> > >      [VIRT_ACPI_GED] = 9,
> > > +    [VIRT_I2C] = 10,
> > >      [VIRT_MMIO] = 16, /* ...to 16 + NUM_VIRTIO_TRANSPORTS - 1 */
> > >      [VIRT_GIC_V2M] = 48, /* ...to 48 + NUM_GICV2M_SPIS - 1 */
> > >      [VIRT_SMMU] = 74,    /* ...to 74 + NUM_SMMU_IRQS - 1 */
> > > @@ -1996,6 +2002,75 @@ static void virt_cpu_post_init(VirtMachineState 
> > > *vms, MemoryRegion *sysmem)
> > >      }
> > >  }
> > >  
> > > +static void create_mctp_test(MachineState *ms)
> > > +{
> > > +    VirtMachineState *vms = VIRT_MACHINE(ms);
> > > +    MemoryRegion *sysmem = get_system_memory();
> > > +    AspeedI2CState *aspeedi2c;
> > > +    struct DeviceState  *dev;
> > > +    char *nodename_i2c_master;
> > > +    char *nodename_i2c_sub;
> > > +    char *nodename_reset;
> > > +    uint32_t clk_phandle, reset_phandle;
> > > +    MemoryRegion *sysmem2;
> > > +   
> > > +    dev = qdev_new("aspeed.i2c-ast2600");
> > > +    aspeedi2c = ASPEED_I2C(dev);
> > > +    object_property_set_link(OBJECT(dev), "dram", OBJECT(ms->ram), 
> > > &error_fatal);
> > > +    sysbus_realize_and_unref(SYS_BUS_DEVICE(dev), &error_fatal);
> > > +    sysbus_mmio_map(SYS_BUS_DEVICE(dev), 0, vms->memmap[VIRT_I2C].base);
> > > +    sysbus_connect_irq(SYS_BUS_DEVICE(&aspeedi2c->busses[0]), 0, 
> > > qdev_get_gpio_in(vms->gic, vms->irqmap[VIRT_I2C]));
> > > +
> > > +    /* I2C bus DT */
> > > +    reset_phandle = qemu_fdt_alloc_phandle(ms->fdt);
> > > +    nodename_reset = g_strdup_printf("/reset@%" PRIx64, 
> > > vms->memmap[VIRT_RESET_FAKE].base);
> > > +    qemu_fdt_add_subnode(ms->fdt, nodename_reset);
> > > +    qemu_fdt_setprop_string(ms->fdt, nodename_reset, "compatible", 
> > > "snps,dw-low-reset");
> > > +    qemu_fdt_setprop_sized_cells(ms->fdt, nodename_reset, "reg",
> > > +                                 2, vms->memmap[VIRT_RESET_FAKE].base,
> > > +                                 2, vms->memmap[VIRT_RESET_FAKE].size);
> > > +    qemu_fdt_setprop_cell(ms->fdt, nodename_reset, "#reset-cells", 0x1);
> > > +    qemu_fdt_setprop_cell(ms->fdt, nodename_reset, "phandle", 
> > > reset_phandle);
> > > +    sysmem2 =  g_new(MemoryRegion, 1);
> > > +    memory_region_init_ram(sysmem2, NULL, "reset", 
> > > vms->memmap[VIRT_RESET_FAKE].size, NULL);
> > > +    memory_region_add_subregion(sysmem, 
> > > vms->memmap[VIRT_RESET_FAKE].base, sysmem2);
> > > +    
> > > +    clk_phandle = qemu_fdt_alloc_phandle(ms->fdt);
> > > +    
> > > +    qemu_fdt_add_subnode(ms->fdt, "/mclk");
> > > +    qemu_fdt_setprop_string(ms->fdt, "/mclk", "compatible", 
> > > "fixed-clock");
> > > +    qemu_fdt_setprop_cell(ms->fdt, "/mclk", "#clock-cells", 0x0);
> > > +    qemu_fdt_setprop_cell(ms->fdt, "/mclk", "clock-frequency", 24000);
> > > +    qemu_fdt_setprop_string(ms->fdt, "/mclk", "clock-output-names", 
> > > "bobsclk");
> > > +    qemu_fdt_setprop_cell(ms->fdt, "/mclk", "phandle", clk_phandle);
> > > +
> > > +    nodename_i2c_master = g_strdup_printf("/i2c@%" PRIx64, 
> > > vms->memmap[VIRT_I2C].base);
> > > +    qemu_fdt_add_subnode(ms->fdt, nodename_i2c_master);
> > > +    qemu_fdt_setprop_string(ms->fdt, nodename_i2c_master, "compatible",  
> > > "aspeed,ast2600-i2c-bus");
> > > +    qemu_fdt_setprop_cells(ms->fdt, nodename_i2c_master, "multi-master");
> > > +    qemu_fdt_setprop_cell(ms->fdt, nodename_i2c_master, "#size-cells", 
> > > 0);
> > > +    qemu_fdt_setprop_cell(ms->fdt, nodename_i2c_master, 
> > > "#address-cells", 1);
> > > +    qemu_fdt_setprop_cell(ms->fdt, nodename_i2c_master, "clocks", 
> > > clk_phandle);
> > > +    qemu_fdt_setprop_string(ms->fdt, nodename_i2c_master, "clock-names", 
> > > "bobsclk");
> > > +    qemu_fdt_setprop(ms->fdt, nodename_i2c_master, "mctp-controller", 
> > > NULL, 0);
> > > +    qemu_fdt_setprop_cells(ms->fdt, nodename_i2c_master, "interrupts", 
> > > GIC_FDT_IRQ_TYPE_SPI,
> > > +                           vms->irqmap[VIRT_I2C], 
> > > GIC_FDT_IRQ_FLAGS_LEVEL_HI);
> > > +    /* Offset to the first bus is 0x80, next one at 0x100 etc */
> > > +    qemu_fdt_setprop_sized_cells(ms->fdt, nodename_i2c_master, "reg",
> > > +                                 2, vms->memmap[VIRT_I2C].base + 0x80,
> > > +                                 2, 0x80);
> > > +    qemu_fdt_setprop_cells(ms->fdt, nodename_i2c_master, "resets", 
> > > reset_phandle,  0);
> > > +
> > > +    nodename_i2c_sub = g_strdup_printf("/i2c@%" PRIx64 "/mctp@%" PRIx64, 
> > > vms->memmap[VIRT_I2C].base, 0x50l);
> > > +    qemu_fdt_add_subnode(ms->fdt, nodename_i2c_sub);
> > > +    qemu_fdt_setprop_string(ms->fdt, nodename_i2c_sub, "compatible",  
> > > "mctp-i2c-controller");
> > > +    qemu_fdt_setprop_sized_cells(ms->fdt, nodename_i2c_sub, "reg", 1, 
> > > 0x50 | 0x40000000);
> > > +
> > > +        
> > > +    /* Slave device - linux doesn't use the presence of dt node for this 
> > > so don't create one*/
> > > +    i2c_slave_create_simple(aspeed_i2c_get_bus(aspeedi2c, 0), 
> > > "i2c_mctp_cxl_switch", 0x4d);
> > > +}
> > > +
> > >  static void machvirt_init(MachineState *machine)
> > >  {
> > >      VirtMachineState *vms = VIRT_MACHINE(machine);
> > > @@ -2289,6 +2364,8 @@ static void machvirt_init(MachineState *machine)
> > >          create_gpio_devices(vms, VIRT_SECURE_GPIO, secure_sysmem);
> > >      }
> > >  
> > > +    create_mctp_test(machine);
> > > +
> > >       /* connect powerdown request */
> > >       vms->powerdown_notifier.notify = virt_powerdown_req;
> > >       qemu_register_powerdown_notifier(&vms->powerdown_notifier);
> > > diff --git a/include/hw/arm/virt.h b/include/hw/arm/virt.h
> > > index 67c08a62af..abbfac7c48 100644
> > > --- a/include/hw/arm/virt.h
> > > +++ b/include/hw/arm/virt.h
> > > @@ -71,6 +71,8 @@ enum {
> > >      VIRT_SMMU,
> > >      VIRT_UART,
> > >      VIRT_MMIO,
> > > +    VIRT_I2C,
> > > +    VIRT_RESET_FAKE,
> > >      VIRT_RTC,
> > >      VIRT_FW_CFG,
> > >      VIRT_PCIE,
> > > -- 
> > > 2.32.0
> > >   
>