Hi,
The CAM Output on the TWOG is a 5V power output. This output is a
power output for a 5V video camera.
If you use this signal direct usually the camera input (1.8V .. 3V)
will be defect.
You can use a 5V relay with this output.
You can also use a normal servo with a micro switch or a camera module
with ppm input in combination with a servo output pin.
for paparazzi 5.03
for the block servo:
<servo name="DC_SHUTTER_SERVO" no"8" min="2000" neutral="1500"
max"1000" />
for the block comand _laws:
<set servo"DC_SUTTER_SERVO" value"@DC_SHUTTER_SERVO"/>
Best regards,
Heinrich
Felix Ruess schrieb:
Or for the Twog:
<load name="digital_cam.xml">
<define name="DC_SHUTTER_GPIO" value="CAM_SWITCH_GPIO"/>
</load>
which equals
<load name="digital_cam.xml">
<define name="DC_SHUTTER_GPIO" value="GPIOB,GPIO22"/>
</load>
If you simply want to control the gpio directly in your own code:
Set the gpio up as output:
gpio_setup_output(CAM_SWITCH_GPIO);
And then set or clear the pin as disired:
gpio_set(CAM_SWITCH_GPIO);
gpio_clear(CAM_SWITCH_GPIO);
On Tue, Dec 2, 2014 at 8:03 PM, Eduardo lavratti
<address@hidden <mailto:address@hidden>> wrote:
For sure you can use the CAM_SW as camera trigger.
Use an optocoupler to connect this pin to your camera.
Use something like this to control the cam_sw pin
<load name="digital_cam.xml">
<define name="DC_SHUTTER_GPIO" value="GPIOC,GPIO12"/>
</load>
> Date: Tue, 2 Dec 2014 06:52:26 -0600
> From: address@hidden
<mailto:address@hidden>
> To: address@hidden <mailto:address@hidden>
> Subject: Re: [Paparazzi-devel] [TWOG] CAM Port Pins
>
> Is there a way to signal it On/Off? I guess voltage regulation
is the
> wrong phrase.
>
> ~Kris
>
> On 12/02/2014 02:46 AM, Rolf Noellenburg wrote:
> > Hello Kris,
> >
> > following the schematics given on the side of your link,
CamSW is on a
> > pin similar to a led switch and is not suitable to control a
servo.
> > Only the outputs SRV0 to SRV7 can drive a servo directly on a
TwoG.
> >
> > By the way: the servo pins don't adjust a voltage in order to
modify
> > the position of the servo but provide a PWM signal which is
translated
> > to a corresponding angle by the servo.
> >
> > Best regards,
> > Rolf
> >
> >
> > Am 02.12.2014 01:03, schrieb Kristofer Von Ahnen:
> >> Is it possible to regulate the voltage of the CamSW pin on
the TWOG
> >> board (http://wiki.paparazziuav.org/wiki/TWOG/v1.0) for
sending a
> >> hardware signal to a separate device? I notice in the
cam_control
> >> module that the servo pins are being used to adjust a camera's
> >> position by sending commands, but can the same be done with
the CamSW
> >> pin?
> >>
> >> Best,
> >> ~Kris
> >>
> >> _______________________________________________
> >> Paparazzi-devel mailing list
> >> address@hidden <mailto:address@hidden>
> >> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
> >>
> >
> >
> > _______________________________________________
> > Paparazzi-devel mailing list
> > address@hidden <mailto:address@hidden>
> > https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>
>
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden <mailto:address@hidden>
> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden <mailto:address@hidden>
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
------------------------------------------------------------------------
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel