Re: [Paparazzi-devel] Could not find STM32 device

Yes Felix I sure do. I originally has a bad cable causing it not to power correctly, but since then it does the cylon flashing pattern when plugged in USB.

Sent from my iPhone

On Jul 25, 2014, at 15:42, "Felix Ruess" <address@hidden> wrote:

Hi,

the board does not seem to be in bootloader mode, it should show up as Lisa/M

Do you see the LEDs flashing like this https://wiki.paparazziuav.org/wiki/Lisa/M_v2.0#Using_luftboot ?

Cheers, Felix

On Fri, Jul 25, 2014 at 5:52 PM, John Voegeli <address@hidden> wrote:

Does not work with sudo either. Tried that last night I thought maybe a permissions issues as well. It just says it cannot find it.

From: AFISH <address@hidden>
Reply-To: Paparazzi UAV devel list <address@hidden>
Date: Friday, July 25, 2014 at 11:47 AM
To: Paparazzi UAV devel list <address@hidden>
Cc: Paparazzi UAV devel list <address@hidden>

Subject: Re: [Paparazzi-devel] Could not find STM32 device

Try to run sudo ./paparazzi, if you get link established, it will shows you need add to some group
—
Sent from Mailbox for iPhone

On Fri, Jul 25, 2014 at 10:16 AM, John Voegeli <address@hidden> wrote:

Yes I have permission I followed those steps... Here is the output for the device that shows up when plugging in the Lisa M to USB.

Bus 002 Device 003: ID 1d50:600f OpenMoko, Inc.
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1d50 OpenMoko, Inc.
idProduct 0x600f
bcdDevice 1.00
iManufacturer 1
iProduct 2
iSerial 3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 27
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 254 Application Specific Interface
bInterfaceSubClass 1 Device Firmware Update
bInterfaceProtocol 2
iInterface 4
Device Firmware Upgrade Interface Descriptor:
bLength 9
bDescriptorType 33
bmAttributes 9
Will Detach
Manifestation Intolerant
Upload Unsupported
Download Supported
wDetachTimeout 255 milliseconds
wTransferSize 2048 bytes
bcdDFUVersion 1.1a

________________________________________
From: paparazzi-devel-bounces+address@hidden <paparazzi-devel-bounces+address@hidden> on behalf of Piotr Esden-Tempski <address@hidden>
Sent: Friday, July 25, 2014 3:18 AM
To: Paparazzi UAV devel list
Subject: Re: [Paparazzi-devel] Could not find STM32 device

Hi John,

Do you have permissions to access the DFU device?

http://wiki.paparazziuav.org/wiki/Installation/Linux#Udev_rules

If you run lsusb -v is the Lisa/M listed?

Cheers,
Piotr

On Jul 24, 2014, at 20:57, John Voegeli <address@hidden> wrote:

> Hey all,
>
> Sorry if this has been answered before. I googled and searched all over the site and could not find anything. I have the new Lisa M 2.1 and I am trying to flash it however I keep getting Could not find STM32 (autopilot) device Failed messages. I have tried everything and am at a loss. Any suggestions?
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden
> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

From:	John Voegeli
Subject:	Re: [Paparazzi-devel] Could not find STM32 device
Date:	Fri, 25 Jul 2014 20:11:25 +0000