libreboot
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Libreboot] [Libreboot T60 from Gluglug] Sometimes my Qualcomm Ather


From: Jorge Araya Navarro
Subject: Re: [Libreboot] [Libreboot T60 from Gluglug] Sometimes my Qualcomm Atheros AR9285 Wireless Network Adapter drops the connection to never reestablish it again (until reboot)
Date: Fri, 13 Nov 2015 12:47:35 -0600
User-agent: mu4e 0.9.13; emacs 24.5.1

Yo! lol.

When this thing happens, I don't have anything playing sounds, so I'm
not sure if the sound card gets affected. I wonder if setting that
kernel flag will prevent this issue from happening. I also too wonder if
unloading and reloading the drivers will do something useful regarding
my issue.

I'm going to set the flag and came back here if something happens.

El viernes 13 de noviembre del 2015 a las 0534 horas, Daniel Tarrero escribió:

> Que pasa Jorge!!
>
> The soon i talk about interrupts, the soon somebody faces problems using
> them!! maybe :)
>
> This seem to be a hardware communication problem. Did you read my last
> two mails? they may bring some information related to this problems.
>
>>> Did you see the DMAR mapping Warning too during boot?? that can have
> something to say here. The fact that a reboot use to solve it, makes me
> think it can be an interrupt conflict.
>
> Your logs say: "module/driver is sending commands to hardware, and it
> didnt respond as we expected"
>
> What can cause this? DMAR mess!!! and also hardware problems, like loose
> of power, changes in hardware that derives in interrupt conflicts like
> pluggin an e-sata, or faulty Atheros chip in the worse case.
>
> You can _force_ module unload (and also, you can
> _unload_dependent_modules_ first). Of course, you have to stop software
> using this hardware too. Maybe something like can make your day:
>
> $ sudo service network-manager stop (stop software)
> $ sudo ifconfig whatever down (unload network)
> $ modprobe -n ath (see dependent modules)
> $ sudo modprobe -f whatever (unload dependencies first)
> $ sudo modprobe -f ath (unload module)
> $ sudo modprobe ath (reload module)
>
> and test!
> You should give some time to the commands to complete, and keep an eye
> in syslog/dmesg to see resoults.
>
> Given that the problem flaps (come and go), i would also check power and
> heat (maybe replace charger with a travel one if you have, and place the
> laptop in a cold environment), and see if fault time changes.
>
> Also there is a previous warning with your sound card that can be
> related:
> snd_hda_intel 0000:00:1b.0: IRQ timing workaround is activated for card
> #0
>
> Is your sound card working when this error happens? If not, we may have
> found the hardware interrupt conflict. They can be using the same
> interrupt, and when sound gets "tweaked" the wifi goes crazy about that
> delay in communications.
>
>
> Good luck!! Im waiting for your experiences! :)
>
> Regards,
> D
>
>
> El jue, 12-11-2015 a las 14:44 -0600, Jorge Araya Navarro escribió:
>> Hello!
>> 
>> I bought my Libreboot T60 from Gluglug in December of last year, and I'm 
>> very happy with a machine
>> which works with 100% Free Software!
>> 
>> Since a couple of months ago is happening something strange to my wifi card, 
>> I first thought the
>> issue was caused by a kernel update but I was wrong. What happens is that at 
>> any random moment every
>> many or so weeks the wifi will drop the connection to never re-establish it 
>> again, until reboot, and
>> after that sometimes the issue continues with the wifi card dropping the 
>> connection once every 60
>> seconds.
>> 
>> Yesterday this thing happened again, so I decided to fire Emacs and takes 
>> some notes and output with
>> org-mode. The first interesting thing is this from `dmesg`:
>> 
>> --8<---------------cut here---------------start------------->8---
>> nov 12 12:43:43 abril.charola kernel: snd_hda_intel 0000:00:1b.0: IRQ timing 
>> workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: Failed to stop TX DMA, 
>> queues=0x00a!
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: DMA failed to stop in 10 ms 
>> AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: Could not stop RX, we could 
>> be confusing the DMA engine when we start RX up
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: Chip reset failed
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: Unable to reset channel, 
>> reset status -22
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: DMA failed to stop in 10 ms 
>> AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: Could not stop RX, we could 
>> be confusing the DMA engine when we start RX up
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: Chip reset failed
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: Unable to reset channel, 
>> reset status -22
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: DMA failed to stop in 10 ms 
>> AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: Could not stop RX, we could 
>> be confusing the DMA engine when we start RX up
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: Chip reset failed
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: Unable to reset channel, 
>> reset status -22
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: DMA failed to stop in 10 ms 
>> AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: Could not stop RX, we could 
>> be confusing the DMA engine when we start RX up
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: Chip reset failed
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: Unable to reset channel, 
>> reset status -22
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: DMA failed to stop in 10 ms 
>> AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
>> nov 12 12:43:44 abril.charola kernel: ath: phy0: Could not stop RX, we could 
>> be confusing the DMA engine when we start RX up
>> nov 12 12:43:45 abril.charola kernel: ath: phy0: Chip reset failed
>> nov 12 12:43:45 abril.charola kernel: ath: phy0: Unable to reset channel, 
>> reset status -22
>> nov 12 12:43:45 abril.charola kernel: ath: phy0: DMA failed to stop in 10 ms 
>> AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
>> nov 12 12:43:45 abril.charola kernel: ath: phy0: Could not stop RX, we could 
>> be confusing the DMA engine when we start RX up
>> nov 12 12:43:45 abril.charola kernel: ath: phy0: Chip reset failed
>> nov 12 12:43:45 abril.charola kernel: ath: phy0: Unable to reset channel, 
>> reset status -22
>> nov 12 12:43:45 abril.charola NetworkManager[445]: <warn>  Connection 
>> disconnected (reason -4)
>> nov 12 12:43:45 abril.charola NetworkManager[445]: <info>  (wlp2s0): 
>> supplicant interface state: completed -> disconnected
>> nov 12 12:43:45 abril.charola kernel: cfg80211: Exceeded CRDA call max 
>> attempts. Not calling CRDA
>> nov 12 12:43:45 abril.charola kernel: ath: phy0: DMA failed to stop in 10 ms 
>> AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
>> nov 12 12:43:45 abril.charola kernel: ath: phy0: Could not stop RX, we could 
>> be confusing the DMA engine when we start RX up
>> nov 12 12:43:45 abril.charola NetworkManager[445]: <info>  (wlp2s0): 
>> supplicant interface state: disconnected -> scanning
>> --8<---------------cut here---------------end--------------->8---
>> 
>> As I don't understand anything with such error messages, my guess is that it 
>> is something
>> serious. after trying to unload the modules related to my wifi driver (ath 
>> (which is impossible
>> because other modules requiring it are being use)) and typing `ifconfig 
>> wlp2s0 down` and what not, I
>> just gave up and restart my laptop. At some point journald register 
>> something interesting:
>> 
>> --8<---------------cut here---------------start------------->8---
>> nov 12 12:44:00 abril.charola kernel: irq 17: nobody cared (try booting with 
>> the "irqpoll" option)
>> nov 12 12:44:00 abril.charola kernel: CPU: 0 PID: 0 Comm: swapper/0 Not 
>> tainted 4.1.11-gnu-1-lts #1
>> nov 12 12:44:00 abril.charola kernel: Hardware name: LENOVO 1951F8G/1951F8G, 
>> BIOS CBET4000 79ETE7WW (2.27 ) 05/18/2015
>> nov 12 12:44:00 abril.charola kernel:  c1609907 4a9301f9 00000000 f5035f54 
>> c14a49ec f53d0e9c f5035f74 c10abbac
>> nov 12 12:44:00 abril.charola kernel:  c1575cc0 00000011 f5035f70 f85611db 
>> f53d0e40 00000000 f5035f98 c10abf22
>> nov 12 12:44:00 abril.charola kernel:  c1329d4a 0003ab5e 00000000 4a9301f9 
>> f53d0e40 c1676e00 00000000 f5035fd4
>> nov 12 12:44:00 abril.charola kernel: Call Trace:
>> nov 12 12:44:00 abril.charola kernel:  [<c14a49ec>] dump_stack+0x41/0x52
>> nov 12 12:44:00 abril.charola kernel:  [<c10abbac>] 
>> __report_bad_irq+0x2c/0xd0
>> nov 12 12:44:00 abril.charola kernel:  [<f85611db>] ? 
>> ath9k_hw_intrpend+0x5b/0x70 [ath9k_hw]
>> nov 12 12:44:00 abril.charola kernel:  [<c10abf22>] 
>> note_interrupt+0x212/0x250
>> nov 12 12:44:00 abril.charola kernel:  [<c1329d4a>] ? 
>> add_interrupt_randomness+0x16a/0x1a0
>> nov 12 12:44:00 abril.charola kernel:  [<c10a99a2>] 
>> handle_irq_event_percpu+0x122/0x190
>> nov 12 12:44:00 abril.charola kernel:  [<c10a99a2>] ? 
>> handle_irq_event_percpu+0x122/0x190
>> nov 12 12:44:00 abril.charola kernel:  [<c10a9a3a>] 
>> handle_irq_event+0x2a/0x50
>> nov 12 12:44:00 abril.charola kernel:  [<c10ac520>] ? 
>> handle_edge_irq+0xe0/0xe0
>> nov 12 12:44:00 abril.charola kernel:  [<c10ac589>] 
>> handle_fasteoi_irq+0x69/0x100
>> nov 12 12:44:00 abril.charola kernel:  [<c1004906>] handle_irq+0x56/0x90
>> nov 12 12:44:00 abril.charola kernel:  <IRQ>  [<c14aa60c>] do_IRQ+0x3c/0xd0
>> nov 12 12:44:00 abril.charola kernel:  [<c14a9c33>] 
>> common_interrupt+0x33/0x38
>> nov 12 12:44:00 abril.charola kernel:  [<c138a553>] ? 
>> cpuidle_enter_state+0x83/0x240
>> nov 12 12:44:00 abril.charola kernel:  [<c138a744>] cpuidle_enter+0x14/0x20
>> nov 12 12:44:00 abril.charola kernel:  [<c108fe89>] 
>> cpu_startup_entry+0x299/0x3a0
>> nov 12 12:44:00 abril.charola kernel:  [<c14a1f67>] rest_init+0x67/0x70
>> nov 12 12:44:00 abril.charola kernel:  [<c167eb51>] start_kernel+0x3c9/0x3e2
>> nov 12 12:44:00 abril.charola kernel:  [<c167e2e3>] 
>> i386_start_kernel+0x91/0x95
>> nov 12 12:44:00 abril.charola kernel: handlers:
>> nov 12 12:44:00 abril.charola kernel: [<f81083c0>] usb_hcd_irq [usbcore]
>> nov 12 12:44:00 abril.charola kernel: [<f860a890>] ath_isr [ath9k]
>> nov 12 12:44:00 abril.charola kernel: Disabling IRQ #17
>> --8<---------------cut here---------------end--------------->8---
>> 
>> Again, I don't know what it says but seems very serious. I'll attach the 
>> full logs in case what I
>> provide is not enough. Hope someone can help me with this.
>> 
>> P.S.: I haven't clean my laptop from dust since I bought it, and it seems it 
>> have some inside, this
>> sporadic issue can be caused by the dust, too.
>> 

-- 
👋 Pax et bonum.
Jorge Araya Navarro
https://es.gravatar.com/shackra



reply via email to

[Prev in Thread] Current Thread [Next in Thread]