Re: [PATCH v1 2/3] riscv/sifive_u: Add a serial property to the sifive_u SoC

[Alistair Francis]

On Thu, Mar 5, 2020 at 4:09 PM Bin Meng <address@hidden> wrote:
>
> Hi Alistair,
>
> On Fri, Mar 6, 2020 at 12:53 AM Alistair Francis <address@hidden> wrote:
> >
> > On Thu, Mar 5, 2020 at 1:31 AM Bin Meng <address@hidden> wrote:
> > >
> > > Hi Alistair,
> > >
> > > On Thu, Mar 5, 2020 at 7:13 AM Alistair Francis <address@hidden> wrote:
> > > >
> > > > On Wed, Mar 4, 2020 at 6:47 AM Bin Meng <address@hidden> wrote:
> > > > >
> > > > > Hi Alistair,
> > > > >
> > > > > On Wed, Mar 4, 2020 at 9:37 AM Alistair Francis
> > > > > <address@hidden> wrote:
> > > > > >
> > > > > > At present the board serial number is hard-coded to 1, and passed
> > > > > > to OTP model during initialization. Firmware (FSBL, U-Boot) uses
> > > > > > the serial number to generate a unique MAC address for the on-chip
> > > > > > ethernet controller. When multiple QEMU 'sifive_u' instances are
> > > > > > created and connected to the same subnet, they all have the same
> > > > > > MAC address hence it creates a unusable network.
> > > > > >
> > > > > > A new "serial" property is introduced to the sifive_u SoC to specify
> > > > > > the board serial number. When not given, the default serial number
> > > > > > 1 is used.
> > > > > >
> > > > > > Suggested-by: Bin Meng <address@hidden>
> > > > > > Signed-off-by: Alistair Francis <address@hidden>
> > > > > > ---
> > > > > >  hw/riscv/sifive_u.c         | 8 +++++++-
> > > > > >  include/hw/riscv/sifive_u.h | 2 ++
> > > > > >  2 files changed, 9 insertions(+), 1 deletion(-)
> > > > > >
> > > > > > diff --git a/hw/riscv/sifive_u.c b/hw/riscv/sifive_u.c
> > > > > > index 9a0145b5b4..e52f9d0bd4 100644
> > > > > > --- a/hw/riscv/sifive_u.c
> > > > > > +++ b/hw/riscv/sifive_u.c
> > > > > > @@ -488,7 +488,7 @@ static void riscv_sifive_u_soc_init(Object *obj)
> > > > > >                            TYPE_SIFIVE_U_PRCI);
> > > > > >      sysbus_init_child_obj(obj, "otp", &s->otp, sizeof(s->otp),
> > > > > >                            TYPE_SIFIVE_U_OTP);
> > > > > > -    qdev_prop_set_uint32(DEVICE(&s->otp), "serial", OTP_SERIAL);
> > > > > > +    qdev_prop_set_uint32(DEVICE(&s->otp), "serial", s->serial);
> > > > > >      sysbus_init_child_obj(obj, "gem", &s->gem, sizeof(s->gem),
> > > > > >                            TYPE_CADENCE_GEM);
> > > > > >  }
> > > > > > @@ -607,10 +607,16 @@ static void 
> > > > > > riscv_sifive_u_soc_realize(DeviceState *dev, Error **errp)
> > > > > >          memmap[SIFIVE_U_GEM_MGMT].base, 
> > > > > > memmap[SIFIVE_U_GEM_MGMT].size);
> > > > > >  }
> > > > > >
> > > > > > +static Property riscv_sifive_u_soc_props[] = {
> > > > > > +    DEFINE_PROP_UINT32("serial", SiFiveUSoCState, serial, 
> > > > > > OTP_SERIAL),
> > > > > > +    DEFINE_PROP_END_OF_LIST()
> > > > >
> > > > > I am not sure how adding another level of property in the SoC could
> > > > > solve the 'make check' error.
> > > >
> > > > The problem is that you were adding a machine property and then you
> > > > had the SoC reach up to the machine object to get the serial value.
> > > > This isn't correct and is why the tests fail.
> > > >
> > >
> > > So looks the failure was due to a check in the test codes only? As I
> > > did not see QEMU crashed during my normal usage.
> >
> > No, the bug was in the actual implementation. You were just lucky that
> > you didn't see any issues as in your case you could access the machine
> > state. The make check probably added the SoC individually and hence
> > caught the bug.
>
> That sounds like the difference that caused the crash in the test.
> Thanks for helping this!

No worries!

Alistair

>
> Regards,
> Bin