[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Qemu-ppc] [PATCH v4 08/20] ppc/pnv: add a LPC controller
|
From: |
Cédric Le Goater |
|
Subject: |
[Qemu-ppc] [PATCH v4 08/20] ppc/pnv: add a LPC controller |
|
Date: |
Mon, 3 Oct 2016 09:24:44 +0200 |
From: Benjamin Herrenschmidt <address@hidden>
The LPC (Low Pin Count) interface on a POWER8 is made accessible to
the system through the ADU (XSCOM interface). This interface is part
of set of units connected together via a local OPB (On-Chip Peripheral
Bus) which act as a bridge between the ADU and the off chip LPC
endpoints, like external flash modules.
The most important units of this OPB are :
- OPB Master: contains the ADU slave logic, a set of internal
registers and the logic to control the OPB.
- LPCHC (LPC HOST Controller): which implements a OPB Slave, a set of
internal registers and the LPC HOST Controller to control the LPC
interface.
Four address spaces are provided to the ADU :
- LPC Bus Firmware Memory
- LPC Bus Memory
- LPC Bus I/O (ISA bus)
- and the registers for the OPB Master and the LPC Host Controller
On POWER8, an intermediate hop is necessary to reach the OPB, through
a unit called the ECCB. OPB commands are simply mangled in ECCB write
commands.
On POWER9, the OPB master address space can be accessed via MMIO. The
logic is same but the code will be simpler as the XSCOM and ECCB hops
are not necessary anymore.
This version of the LPC controller model doesn't yet implement support
for the SerIRQ deserializer present in the Naples version of the chip
though some preliminary work is there.
Signed-off-by: Benjamin Herrenschmidt <address@hidden>
[clg: - updated for qemu-2.7
- ported on latest PowerNV patchset
- changed the XSCOM interface to fit new model
- QOMified the model
- moved the ISA hunks in another patch
- removed printf logging
- added a couple of UNIMP logging
- rewrote commit log ]
Signed-off-by: Cédric Le Goater <address@hidden>
---
Todo:
- rework the address_space read/write ops as they should be shared
with the P9 support.
Changes since v3:
- rewrote commit log
- fixed appendprop
hw/ppc/Makefile.objs | 2 +-
hw/ppc/pnv.c | 9 +
hw/ppc/pnv_lpc.c | 471 +++++++++++++++++++++++++++++++++++++++++++++
include/hw/ppc/pnv.h | 3 +
include/hw/ppc/pnv_lpc.h | 67 +++++++
include/hw/ppc/pnv_xscom.h | 3 +
6 files changed, 554 insertions(+), 1 deletion(-)
create mode 100644 hw/ppc/pnv_lpc.c
create mode 100644 include/hw/ppc/pnv_lpc.h
diff --git a/hw/ppc/Makefile.objs b/hw/ppc/Makefile.objs
index 08c213c40684..ebc72af0a7c6 100644
--- a/hw/ppc/Makefile.objs
+++ b/hw/ppc/Makefile.objs
@@ -6,7 +6,7 @@ obj-$(CONFIG_PSERIES) += spapr_hcall.o spapr_iommu.o
spapr_rtas.o
obj-$(CONFIG_PSERIES) += spapr_pci.o spapr_rtc.o spapr_drc.o spapr_rng.o
obj-$(CONFIG_PSERIES) += spapr_cpu_core.o
# IBM PowerNV
-obj-$(CONFIG_POWERNV) += pnv.o pnv_xscom.o pnv_core.o
+obj-$(CONFIG_POWERNV) += pnv.o pnv_xscom.o pnv_core.o pnv_lpc.o
ifeq ($(CONFIG_PCI)$(CONFIG_PSERIES)$(CONFIG_LINUX), yyy)
obj-y += spapr_pci_vfio.o
endif
diff --git a/hw/ppc/pnv.c b/hw/ppc/pnv.c
index ffe245fe59d2..e41244294435 100644
--- a/hw/ppc/pnv.c
+++ b/hw/ppc/pnv.c
@@ -563,6 +563,9 @@ static void pnv_chip_init(Object *obj)
PnvChipClass *pcc = PNV_CHIP_GET_CLASS(chip);
chip->xscom_base = pcc->xscom_base;
+
+ object_initialize(&chip->lpc, sizeof(chip->lpc), TYPE_PNV_LPC);
+ object_property_add_child(obj, "lpc", OBJECT(&chip->lpc), NULL);
}
static void pnv_chip_realize(DeviceState *dev, Error **errp)
@@ -626,6 +629,12 @@ static void pnv_chip_realize(DeviceState *dev, Error
**errp)
&PNV_CORE(pnv_core)->xscom_regs);
}
g_free(typename);
+
+ /* Create LPC controller */
+ object_property_set_bool(OBJECT(&chip->lpc), true, "realized",
+ &error_fatal);
+ memory_region_add_subregion(&chip->xscom, PNV_XSCOM_LPC_BASE << 3,
+ &chip->lpc.xscom_regs);
}
static Property pnv_chip_properties[] = {
diff --git a/hw/ppc/pnv_lpc.c b/hw/ppc/pnv_lpc.c
new file mode 100644
index 000000000000..210cc1cff167
--- /dev/null
+++ b/hw/ppc/pnv_lpc.c
@@ -0,0 +1,471 @@
+/*
+ * QEMU PowerPC PowerNV LPC controller
+ *
+ * Copyright (c) 2016, IBM Corporation.
+ *
+ * This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU Lesser General Public
+ * License as published by the Free Software Foundation; either
+ * version 2 of the License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public
+ * License along with this library; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "qemu/osdep.h"
+#include "sysemu/sysemu.h"
+#include "target-ppc/cpu.h"
+#include "qapi/error.h"
+#include "qemu/log.h"
+
+#include "hw/ppc/pnv_lpc.h"
+#include "hw/ppc/pnv.h"
+#include "hw/ppc/fdt.h"
+
+#include <libfdt.h>
+
+enum {
+ ECCB_CTL = 0,
+ ECCB_RESET = 1,
+ ECCB_STAT = 2,
+ ECCB_DATA = 3,
+};
+
+/* OPB Master LS registers */
+#define OPB_MASTER_LS_IRQ_STAT 0x50
+#define OPB_MASTER_IRQ_LPC 0x00000800
+#define OPB_MASTER_LS_IRQ_MASK 0x54
+#define OPB_MASTER_LS_IRQ_POL 0x58
+#define OPB_MASTER_LS_IRQ_INPUT 0x5c
+
+/* LPC HC registers */
+#define LPC_HC_FW_SEG_IDSEL 0x24
+#define LPC_HC_FW_RD_ACC_SIZE 0x28
+#define LPC_HC_FW_RD_1B 0x00000000
+#define LPC_HC_FW_RD_2B 0x01000000
+#define LPC_HC_FW_RD_4B 0x02000000
+#define LPC_HC_FW_RD_16B 0x04000000
+#define LPC_HC_FW_RD_128B 0x07000000
+#define LPC_HC_IRQSER_CTRL 0x30
+#define LPC_HC_IRQSER_EN 0x80000000
+#define LPC_HC_IRQSER_QMODE 0x40000000
+#define LPC_HC_IRQSER_START_MASK 0x03000000
+#define LPC_HC_IRQSER_START_4CLK 0x00000000
+#define LPC_HC_IRQSER_START_6CLK 0x01000000
+#define LPC_HC_IRQSER_START_8CLK 0x02000000
+#define LPC_HC_IRQMASK 0x34 /* same bit defs as LPC_HC_IRQSTAT */
+#define LPC_HC_IRQSTAT 0x38
+#define LPC_HC_IRQ_SERIRQ0 0x80000000 /* all bits down to ... */
+#define LPC_HC_IRQ_SERIRQ16 0x00008000 /* IRQ16=IOCHK#, IRQ2=SMI#
*/
+#define LPC_HC_IRQ_SERIRQ_ALL 0xffff8000
+#define LPC_HC_IRQ_LRESET 0x00000400
+#define LPC_HC_IRQ_SYNC_ABNORM_ERR 0x00000080
+#define LPC_HC_IRQ_SYNC_NORESP_ERR 0x00000040
+#define LPC_HC_IRQ_SYNC_NORM_ERR 0x00000020
+#define LPC_HC_IRQ_SYNC_TIMEOUT_ERR 0x00000010
+#define LPC_HC_IRQ_SYNC_TARG_TAR_ERR 0x00000008
+#define LPC_HC_IRQ_SYNC_BM_TAR_ERR 0x00000004
+#define LPC_HC_IRQ_SYNC_BM0_REQ 0x00000002
+#define LPC_HC_IRQ_SYNC_BM1_REQ 0x00000001
+#define LPC_HC_ERROR_ADDRESS 0x40
+
+#define LPC_OPB_SIZE 0x100000000ull
+
+#define ISA_IO_SIZE 0x00010000
+#define ISA_MEM_SIZE 0x10000000
+#define LPC_IO_OPB_ADDR 0xd0010000
+#define LPC_IO_OPB_SIZE 0x00010000
+#define LPC_MEM_OPB_ADDR 0xe0010000
+#define LPC_MEM_OPB_SIZE 0x10000000
+#define LPC_FW_OPB_ADDR 0xf0000000
+#define LPC_FW_OPB_SIZE 0x10000000
+
+#define LPC_OPB_REGS_OPB_ADDR 0xc0010000
+#define LPC_OPB_REGS_OPB_SIZE 0x00002000
+#define LPC_HC_REGS_OPB_ADDR 0xc0012000
+#define LPC_HC_REGS_OPB_SIZE 0x00001000
+
+
+/*
+ * TODO: the "primary" cell should only be added on chip 0. This is
+ * how skiboot chooses the default LPC controller on multichip
+ * systems.
+ *
+ * It would be easly done if we can change the populate() interface to
+ * replace the PnvXScomInterface parameter by a PnvChip one
+ */
+static int pnv_lpc_populate(PnvXScomInterface *dev, void *fdt, int
xscom_offset)
+{
+ const char compat[] = "ibm,power8-lpc\0ibm,lpc";
+ char *name;
+ int offset;
+ uint32_t lpc_pcba = PNV_XSCOM_LPC_BASE;
+ uint32_t reg[] = {
+ cpu_to_be32(lpc_pcba),
+ cpu_to_be32(PNV_XSCOM_LPC_SIZE)
+ };
+
+ name = g_strdup_printf("address@hidden", lpc_pcba);
+ offset = fdt_add_subnode(fdt, xscom_offset, name);
+ _FDT(offset);
+ g_free(name);
+
+ _FDT((fdt_setprop(fdt, offset, "reg", reg, sizeof(reg))));
+ _FDT((fdt_setprop_cell(fdt, offset, "#address-cells", 2)));
+ _FDT((fdt_setprop_cell(fdt, offset, "#size-cells", 1)));
+ _FDT((fdt_setprop(fdt, offset, "primary", NULL, 0)));
+ _FDT((fdt_setprop(fdt, offset, "compatible", compat, sizeof(compat))));
+ return 0;
+}
+
+/*
+ * These read/write handlers of the OPB address space should be common
+ * with the P9 LPC Controller which uses direct MMIOs.
+ *
+ * TODO: rework to use address_space_stq() and address_space_ldq()
+ * instead.
+ */
+static bool opb_read(PnvLpcController *lpc, uint32_t addr, uint8_t *data,
+ int sz)
+{
+ bool success;
+
+ /* XXX Handle access size limits and FW read caching here */
+ success = !address_space_rw(&lpc->opb_as, addr, MEMTXATTRS_UNSPECIFIED,
+ data, sz, false);
+
+ return success;
+}
+
+static bool opb_write(PnvLpcController *lpc, uint32_t addr, uint8_t *data,
+ int sz)
+{
+ bool success;
+
+ /* XXX Handle access size limits here */
+ success = !address_space_rw(&lpc->opb_as, addr, MEMTXATTRS_UNSPECIFIED,
+ data, sz, true);
+
+ return success;
+}
+
+#define ECCB_CTL_READ (1ull << (63 - 15))
+#define ECCB_CTL_SZ_LSH (63 - 7)
+#define ECCB_CTL_SZ_MASK (0xfull << ECCB_CTL_SZ_LSH)
+#define ECCB_CTL_ADDR_MASK 0xffffffffu;
+
+#define ECCB_STAT_OP_DONE (1ull << (63 - 52))
+#define ECCB_STAT_OP_ERR (1ull << (63 - 52))
+#define ECCB_STAT_RD_DATA_LSH (63 - 37)
+#define ECCB_STAT_RD_DATA_MASK (0xffffffff << ECCB_STAT_RD_DATA_LSH)
+
+static void pnv_lpc_do_eccb(PnvLpcController *lpc, uint64_t cmd)
+{
+ /* XXX Check for magic bits at the top, addr size etc... */
+ unsigned int sz = (cmd & ECCB_CTL_SZ_MASK) >> ECCB_CTL_SZ_LSH;
+ uint32_t opb_addr = cmd & ECCB_CTL_ADDR_MASK;
+ uint8_t data[4];
+ bool success;
+
+ if (cmd & ECCB_CTL_READ) {
+ success = opb_read(lpc, opb_addr, data, sz);
+ if (success) {
+ lpc->eccb_stat_reg = ECCB_STAT_OP_DONE |
+ (((uint64_t)data[0]) << 24 |
+ ((uint64_t)data[1]) << 16 |
+ ((uint64_t)data[2]) << 8 |
+ ((uint64_t)data[3])) << ECCB_STAT_RD_DATA_LSH;
+ } else {
+ lpc->eccb_stat_reg = ECCB_STAT_OP_DONE |
+ (0xffffffffull << ECCB_STAT_RD_DATA_LSH);
+ }
+ } else {
+ data[0] = lpc->eccb_data_reg >> 24;
+ data[1] = lpc->eccb_data_reg >> 16;
+ data[2] = lpc->eccb_data_reg >> 8;
+ data[3] = lpc->eccb_data_reg;
+
+ success = opb_write(lpc, opb_addr, data, sz);
+ lpc->eccb_stat_reg = ECCB_STAT_OP_DONE;
+ }
+ /* XXX Which error bit (if any) to signal OPB error ? */
+}
+
+static uint64_t pnv_lpc_xscom_read(void *opaque, hwaddr addr, unsigned size)
+{
+ PnvLpcController *lpc = PNV_LPC(opaque);
+ uint32_t offset = addr >> 3;
+ uint64_t val = 0;
+
+ switch (offset & 3) {
+ case ECCB_CTL:
+ case ECCB_RESET:
+ val = 0;
+ break;
+ case ECCB_STAT:
+ val = lpc->eccb_stat_reg;
+ lpc->eccb_stat_reg = 0;
+ break;
+ case ECCB_DATA:
+ val = ((uint64_t)lpc->eccb_data_reg) << 32;
+ break;
+ }
+ return val;
+}
+
+static void pnv_lpc_xscom_write(void *opaque, hwaddr addr,
+ uint64_t val, unsigned size)
+{
+ PnvLpcController *lpc = PNV_LPC(opaque);
+ uint32_t offset = addr >> 3;
+
+ switch (offset & 3) {
+ case ECCB_CTL:
+ pnv_lpc_do_eccb(lpc, val);
+ break;
+ case ECCB_RESET:
+ /* XXXX */
+ break;
+ case ECCB_STAT:
+ break;
+ case ECCB_DATA:
+ lpc->eccb_data_reg = val >> 32;
+ break;
+ }
+}
+
+static const MemoryRegionOps pnv_lpc_xscom_ops = {
+ .read = pnv_lpc_xscom_read,
+ .write = pnv_lpc_xscom_write,
+ .valid.min_access_size = 8,
+ .valid.max_access_size = 8,
+ .impl.min_access_size = 8,
+ .impl.max_access_size = 8,
+ .endianness = DEVICE_BIG_ENDIAN,
+};
+
+static uint64_t lpc_hc_read(void *opaque, hwaddr addr, unsigned size)
+{
+ PnvLpcController *lpc = opaque;
+ uint64_t val = 0xfffffffffffffffful;
+
+ switch (addr) {
+ case LPC_HC_FW_SEG_IDSEL:
+ val = lpc->lpc_hc_fw_seg_idsel;
+ break;
+ case LPC_HC_FW_RD_ACC_SIZE:
+ val = lpc->lpc_hc_fw_rd_acc_size;
+ break;
+ case LPC_HC_IRQSER_CTRL:
+ val = lpc->lpc_hc_irqser_ctrl;
+ break;
+ case LPC_HC_IRQMASK:
+ val = lpc->lpc_hc_irqmask;
+ break;
+ case LPC_HC_IRQSTAT:
+ val = lpc->lpc_hc_irqstat;
+ break;
+ case LPC_HC_ERROR_ADDRESS:
+ val = lpc->lpc_hc_error_addr;
+ break;
+ default:
+ qemu_log_mask(LOG_UNIMP, "LPC HC Unimplemented register: Ox%"
+ HWADDR_PRIx "\n", addr);
+ }
+ return val;
+}
+
+static void lpc_hc_write(void *opaque, hwaddr addr, uint64_t val,
+ unsigned size)
+{
+ PnvLpcController *lpc = opaque;
+
+ /* XXX Filter out reserved bits */
+
+ switch (addr) {
+ case LPC_HC_FW_SEG_IDSEL:
+ /* XXX Actually figure out how that works as this impact
+ * memory regions/aliases
+ */
+ lpc->lpc_hc_fw_seg_idsel = val;
+ break;
+ case LPC_HC_FW_RD_ACC_SIZE:
+ lpc->lpc_hc_fw_rd_acc_size = val;
+ break;
+ case LPC_HC_IRQSER_CTRL:
+ lpc->lpc_hc_irqser_ctrl = val;
+ break;
+ case LPC_HC_IRQMASK:
+ lpc->lpc_hc_irqmask = val;
+ break;
+ case LPC_HC_IRQSTAT:
+ lpc->lpc_hc_irqstat &= ~val;
+ break;
+ case LPC_HC_ERROR_ADDRESS:
+ break;
+ default:
+ qemu_log_mask(LOG_UNIMP, "LPC HC Unimplemented register: Ox%"
+ HWADDR_PRIx "\n", addr);
+ }
+}
+
+static const MemoryRegionOps lpc_hc_ops = {
+ .read = lpc_hc_read,
+ .write = lpc_hc_write,
+ .endianness = DEVICE_BIG_ENDIAN,
+ .valid = {
+ .min_access_size = 4,
+ .max_access_size = 4,
+ },
+ .impl = {
+ .min_access_size = 4,
+ .max_access_size = 4,
+ },
+};
+
+static uint64_t opb_master_read(void *opaque, hwaddr addr, unsigned size)
+{
+ PnvLpcController *lpc = opaque;
+ uint64_t val = 0xfffffffffffffffful;
+
+ switch (addr) {
+ case OPB_MASTER_LS_IRQ_STAT:
+ val = lpc->opb_irq_stat;
+ break;
+ case OPB_MASTER_LS_IRQ_MASK:
+ val = lpc->opb_irq_mask;
+ break;
+ case OPB_MASTER_LS_IRQ_POL:
+ val = lpc->opb_irq_pol;
+ break;
+ case OPB_MASTER_LS_IRQ_INPUT:
+ val = lpc->opb_irq_input;
+ break;
+ default:
+ qemu_log_mask(LOG_UNIMP, "OPB MASTER Unimplemented register: Ox%"
+ HWADDR_PRIx "\n", addr);
+ }
+
+ return val;
+}
+
+static void opb_master_write(void *opaque, hwaddr addr,
+ uint64_t val, unsigned size)
+{
+ PnvLpcController *lpc = opaque;
+
+ switch (addr) {
+ case OPB_MASTER_LS_IRQ_STAT:
+ lpc->opb_irq_stat &= ~val;
+ break;
+ case OPB_MASTER_LS_IRQ_MASK:
+ /* XXX Filter out reserved bits */
+ lpc->opb_irq_mask = val;
+ break;
+ case OPB_MASTER_LS_IRQ_POL:
+ /* XXX Filter out reserved bits */
+ lpc->opb_irq_pol = val;
+ break;
+ case OPB_MASTER_LS_IRQ_INPUT:
+ /* Read only */
+ break;
+ default:
+ qemu_log_mask(LOG_UNIMP, "OPB MASTER Unimplemented register: Ox%"
+ HWADDR_PRIx "\n", addr);
+ }
+}
+
+static const MemoryRegionOps opb_master_ops = {
+ .read = opb_master_read,
+ .write = opb_master_write,
+ .endianness = DEVICE_BIG_ENDIAN,
+ .valid = {
+ .min_access_size = 4,
+ .max_access_size = 4,
+ },
+ .impl = {
+ .min_access_size = 4,
+ .max_access_size = 4,
+ },
+};
+
+static void pnv_lpc_realize(DeviceState *dev, Error **errp)
+{
+ PnvLpcController *lpc = PNV_LPC(dev);
+
+ /* Reg inits */
+ lpc->lpc_hc_fw_rd_acc_size = LPC_HC_FW_RD_4B;
+
+ /* Create address space and backing MR for the OPB bus */
+ memory_region_init(&lpc->opb_mr, OBJECT(dev), "lpc-opb", 0x100000000ull);
+ address_space_init(&lpc->opb_as, &lpc->opb_mr, "lpc-opb");
+
+ /* Create ISA IO and Mem space regions which are the root of
+ * the ISA bus (ie, ISA address spaces). We don't create a
+ * separate one for FW which we alias to memory.
+ */
+ memory_region_init(&lpc->isa_io, OBJECT(dev), "isa-io", ISA_IO_SIZE);
+ memory_region_init(&lpc->isa_mem, OBJECT(dev), "isa-mem", ISA_MEM_SIZE);
+
+ /* Create windows from the OPB space to the ISA space */
+ memory_region_init_alias(&lpc->opb_isa_io, OBJECT(dev), "lpc-isa-io",
+ &lpc->isa_io, 0, LPC_IO_OPB_SIZE);
+ memory_region_add_subregion(&lpc->opb_mr, LPC_IO_OPB_ADDR,
+ &lpc->opb_isa_io);
+ memory_region_init_alias(&lpc->opb_isa_mem, OBJECT(dev), "lpc-isa-mem",
+ &lpc->isa_mem, 0, LPC_MEM_OPB_SIZE);
+ memory_region_add_subregion(&lpc->opb_mr, LPC_MEM_OPB_ADDR,
+ &lpc->opb_isa_mem);
+ memory_region_init_alias(&lpc->opb_isa_fw, OBJECT(dev), "lpc-isa-fw",
+ &lpc->isa_mem, 0, LPC_FW_OPB_SIZE);
+ memory_region_add_subregion(&lpc->opb_mr, LPC_FW_OPB_ADDR,
+ &lpc->opb_isa_fw);
+
+ /* Create MMIO regions for LPC HC and OPB registers */
+ memory_region_init_io(&lpc->opb_master_regs, OBJECT(dev), &opb_master_ops,
+ lpc, "lpc-opb-master", LPC_OPB_REGS_OPB_SIZE);
+ memory_region_add_subregion(&lpc->opb_mr, LPC_OPB_REGS_OPB_ADDR,
+ &lpc->opb_master_regs);
+ memory_region_init_io(&lpc->lpc_hc_regs, OBJECT(dev), &lpc_hc_ops, lpc,
+ "lpc-hc", LPC_HC_REGS_OPB_SIZE);
+ memory_region_add_subregion(&lpc->opb_mr, LPC_HC_REGS_OPB_ADDR,
+ &lpc->lpc_hc_regs);
+
+ /* XScom region for LPC registers */
+ memory_region_init_io(&lpc->xscom_regs, OBJECT(dev),
+ &pnv_lpc_xscom_ops, lpc, "xscom-lpc",
+ PNV_XSCOM_LPC_SIZE << 3);
+}
+
+static void pnv_lpc_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ PnvXScomInterfaceClass *xdc = PNV_XSCOM_INTERFACE_CLASS(klass);
+
+ xdc->populate = pnv_lpc_populate;
+
+ dc->realize = pnv_lpc_realize;
+}
+
+static const TypeInfo pnv_lpc_info = {
+ .name = TYPE_PNV_LPC,
+ .parent = TYPE_DEVICE,
+ .instance_size = sizeof(PnvLpcController),
+ .class_init = pnv_lpc_class_init,
+ .interfaces = (InterfaceInfo[]) {
+ { TYPE_PNV_XSCOM_INTERFACE },
+ { }
+ }
+};
+
+static void pnv_lpc_register_types(void)
+{
+ type_register_static(&pnv_lpc_info);
+}
+
+type_init(pnv_lpc_register_types)
diff --git a/include/hw/ppc/pnv.h b/include/hw/ppc/pnv.h
index f89eddb6e5e0..e586ff4e735e 100644
--- a/include/hw/ppc/pnv.h
+++ b/include/hw/ppc/pnv.h
@@ -22,6 +22,7 @@
#include "hw/boards.h"
#include "hw/sysbus.h"
#include "hw/ppc/pnv_xscom.h"
+#include "hw/ppc/pnv_lpc.h"
#define TYPE_PNV_CHIP "powernv-chip"
#define PNV_CHIP(obj) OBJECT_CHECK(PnvChip, (obj), TYPE_PNV_CHIP)
@@ -52,6 +53,8 @@ typedef struct PnvChip {
uint32_t nr_cores;
uint64_t cores_mask;
void *cores;
+
+ PnvLpcController lpc;
} PnvChip;
typedef struct PnvChipClass {
diff --git a/include/hw/ppc/pnv_lpc.h b/include/hw/ppc/pnv_lpc.h
new file mode 100644
index 000000000000..38e5506975aa
--- /dev/null
+++ b/include/hw/ppc/pnv_lpc.h
@@ -0,0 +1,67 @@
+/*
+ * QEMU PowerPC PowerNV LPC controller
+ *
+ * Copyright (c) 2016, IBM Corporation.
+ *
+ * This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU Lesser General Public
+ * License as published by the Free Software Foundation; either
+ * version 2 of the License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public
+ * License along with this library; if not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef _PPC_PNV_LPC_H
+#define _PPC_PNV_LPC_H
+
+#define TYPE_PNV_LPC "pnv-lpc"
+#define PNV_LPC(obj) \
+ OBJECT_CHECK(PnvLpcController, (obj), TYPE_PNV_LPC)
+
+typedef struct PnvLpcController {
+ DeviceState parent;
+
+ uint64_t eccb_stat_reg;
+ uint32_t eccb_data_reg;
+
+ /* OPB bus */
+ MemoryRegion opb_mr;
+ AddressSpace opb_as;
+
+ /* ISA IO and Memory space */
+ MemoryRegion isa_io;
+ MemoryRegion isa_mem;
+
+ /* Windows from OPB to ISA (aliases) */
+ MemoryRegion opb_isa_io;
+ MemoryRegion opb_isa_mem;
+ MemoryRegion opb_isa_fw;
+
+ /* Registers */
+ MemoryRegion lpc_hc_regs;
+ MemoryRegion opb_master_regs;
+
+ /* OPB Master LS registers */
+ uint32_t opb_irq_stat;
+ uint32_t opb_irq_mask;
+ uint32_t opb_irq_pol;
+ uint32_t opb_irq_input;
+
+ /* LPC HC registers */
+ uint32_t lpc_hc_fw_seg_idsel;
+ uint32_t lpc_hc_fw_rd_acc_size;
+ uint32_t lpc_hc_irqser_ctrl;
+ uint32_t lpc_hc_irqmask;
+ uint32_t lpc_hc_irqstat;
+ uint32_t lpc_hc_error_addr;
+
+ /* XSCOM registers */
+ MemoryRegion xscom_regs;
+} PnvLpcController;
+
+#endif /* _PPC_PNV_LPC_H */
diff --git a/include/hw/ppc/pnv_xscom.h b/include/hw/ppc/pnv_xscom.h
index 79975a6cbe46..3b8a8b4fc6ff 100644
--- a/include/hw/ppc/pnv_xscom.h
+++ b/include/hw/ppc/pnv_xscom.h
@@ -60,6 +60,9 @@ typedef struct PnvXScomInterfaceClass {
#define PNV_XSCOM_EX_CORE_BASE(i) (PNV_XSCOM_EX_BASE | (((uint64_t)i) << 24))
#define PNV_XSCOM_EX_CORE_SIZE 0x100000
+#define PNV_XSCOM_LPC_BASE 0xb0020
+#define PNV_XSCOM_LPC_SIZE 0x4
+
extern void pnv_xscom_realize(PnvChip *chip, Error **errp);
extern int pnv_xscom_populate(PnvChip *chip, void *fdt, int offset);
--
2.7.4