qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [PATCH 09/12] next-cube.c: move static old_scr2 variable to NeXTPC


From: Thomas Huth
Subject: Re: [PATCH 09/12] next-cube.c: move static old_scr2 variable to NeXTPC
Date: Sat, 16 Dec 2023 21:18:48 +0100

Am Fri, 15 Dec 2023 20:00:06 +0000
schrieb Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>:

> Move the old_scr2 variable to NeXTPC so that the old SCR2 register state is
> stored along with the current SCR2 state.
> 
> Since the SCR2 register is 32-bits wide, convert old_scr2 to uint32_t and
> update the SCR2 register access code to allow unaligned writes.
> 
> Note that this is a migration break, but as nothing will currently boot then
> we do not need to worry about this now.
> 
> Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
> ---
>  hw/m68k/next-cube.c | 12 +++++++++---
>  1 file changed, 9 insertions(+), 3 deletions(-)
> 
> diff --git a/hw/m68k/next-cube.c b/hw/m68k/next-cube.c
> index 7ffd1c412e..fd707b4b54 100644
> --- a/hw/m68k/next-cube.c
> +++ b/hw/m68k/next-cube.c
> @@ -91,6 +91,7 @@ struct NeXTPC {
>  
>      uint32_t scr1;
>      uint32_t scr2;
> +    uint32_t old_scr2;
>      uint32_t int_mask;
>      uint32_t int_status;
>      uint32_t led;
> @@ -137,8 +138,7 @@ static void next_scr2_led_update(NeXTPC *s)
>  
>  static void nextscr2_write(NeXTPC *s, uint32_t val, int size)
>  {
> -    static uint8_t old_scr2;
> -    uint8_t scr2_2;
> +    uint8_t old_scr2, scr2_2;
>      NextRtc *rtc = &s->rtc;
>  
>      if (size == 4) {
> @@ -147,6 +147,8 @@ static void nextscr2_write(NeXTPC *s, uint32_t val, int 
> size)
>          scr2_2 = val & 0xFF;
>      }
>  
> +    old_scr2 = (s->old_scr2 >> 8) & 0xff;
> +
>      if (scr2_2 & 0x1) {
>          /* DPRINTF("RTC %x phase %i\n", scr2_2, rtc->phase); */
>          if (rtc->phase == -1) {
> @@ -255,7 +257,6 @@ static void nextscr2_write(NeXTPC *s, uint32_t val, int 
> size)
>      }
>      s->scr2 = val & 0xFFFF00FF;
>      s->scr2 |= scr2_2 << 8;
> -    old_scr2 = scr2_2;
>  }
>  
>  static uint64_t next_mmio_read(void *opaque, hwaddr addr, unsigned size)
> @@ -321,8 +322,11 @@ static void next_mmio_write(void *opaque, hwaddr addr, 
> uint64_t val,
>          break;
>  
>      case 0xd000 ... 0xd003:
> +        s->scr2 = deposit32(s->scr2, (4 - (addr - 0xd000) - size) << 3,
> +                            size << 3, val);
>          next_scr2_led_update(s);
>          nextscr2_write(s, val, size);
> +        s->old_scr2 = s->scr2;
>          break;

Ah, I see, now you set s->scr2 here already ... I think you should swap the
order of the patches 08 and 09...?

 Thomas



reply via email to

[Prev in Thread] Current Thread [Next in Thread]