qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[PATCH v3 43/47] e1000e: Notify only new interrupts


From: Akihiko Odaki
Subject: [PATCH v3 43/47] e1000e: Notify only new interrupts
Date: Sun, 23 Apr 2023 13:18:29 +0900

In MSI-X mode, if there are interrupts already notified but not cleared
and a new interrupt arrives, e1000e incorrectly notifies the notified
ones again along with the new one.

To fix this issue, replace e1000e_update_interrupt_state() with
two new functions: e1000e_raise_interrupts() and
e1000e_lower_interrupts(). These functions don't only raise or lower
interrupts, but it also performs register writes which updates the
interrupt state. Before it performs a register write, these function
determines the interrupts already raised, and compares with the
interrupts raised after the register write to determine the interrupts
to notify.

The introduction of these functions made tracepoints which assumes that
the caller of e1000e_update_interrupt_state() performs register writes
obsolete. These tracepoints are now removed, and alternative ones are
added to the new functions.

Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
---
 hw/net/e1000e_core.h |   2 -
 hw/net/e1000e_core.c | 153 +++++++++++++++++++------------------------
 hw/net/trace-events  |   2 +
 3 files changed, 69 insertions(+), 88 deletions(-)

diff --git a/hw/net/e1000e_core.h b/hw/net/e1000e_core.h
index 213a70530d..66b025cc43 100644
--- a/hw/net/e1000e_core.h
+++ b/hw/net/e1000e_core.h
@@ -111,8 +111,6 @@ struct E1000Core {
     PCIDevice *owner;
     void (*owner_start_recv)(PCIDevice *d);
 
-    uint32_t msi_causes_pending;
-
     int64_t timadj;
 };
 
diff --git a/hw/net/e1000e_core.c b/hw/net/e1000e_core.c
index 347162a9d0..78373d7db7 100644
--- a/hw/net/e1000e_core.c
+++ b/hw/net/e1000e_core.c
@@ -165,14 +165,14 @@ e1000e_intrmgr_on_throttling_timer(void *opaque)
 
     timer->running = false;
 
-    if (msi_enabled(timer->core->owner)) {
-        trace_e1000e_irq_msi_notify_postponed();
-        /* Clear msi_causes_pending to fire MSI eventually */
-        timer->core->msi_causes_pending = 0;
-        e1000e_set_interrupt_cause(timer->core, 0);
-    } else {
-        trace_e1000e_irq_legacy_notify_postponed();
-        e1000e_set_interrupt_cause(timer->core, 0);
+    if (timer->core->mac[IMS] & timer->core->mac[ICR]) {
+        if (msi_enabled(timer->core->owner)) {
+            trace_e1000e_irq_msi_notify_postponed();
+            msi_notify(timer->core->owner, 0);
+        } else {
+            trace_e1000e_irq_legacy_notify_postponed();
+            e1000e_raise_legacy_irq(timer->core);
+        }
     }
 }
 
@@ -366,10 +366,6 @@ static void
 e1000e_intrmgr_fire_all_timers(E1000ECore *core)
 {
     int i;
-    uint32_t val = e1000e_intmgr_collect_delayed_causes(core);
-
-    trace_e1000e_irq_adding_delayed_causes(val, core->mac[ICR]);
-    core->mac[ICR] |= val;
 
     if (core->itr.running) {
         timer_del(core->itr.timer);
@@ -1974,13 +1970,6 @@ 
void(*e1000e_phyreg_writeops[E1000E_PHY_PAGES][E1000E_PHY_PAGE_SIZE])
     }
 };
 
-static inline void
-e1000e_clear_ims_bits(E1000ECore *core, uint32_t bits)
-{
-    trace_e1000e_irq_clear_ims(bits, core->mac[IMS], core->mac[IMS] & ~bits);
-    core->mac[IMS] &= ~bits;
-}
-
 static inline bool
 e1000e_postpone_interrupt(E1000IntrDelayTimer *timer)
 {
@@ -2038,7 +2027,6 @@ e1000e_msix_notify_one(E1000ECore *core, uint32_t cause, 
uint32_t int_cfg)
     effective_eiac = core->mac[EIAC] & cause;
 
     core->mac[ICR] &= ~effective_eiac;
-    core->msi_causes_pending &= ~effective_eiac;
 
     if (!(core->mac[CTRL_EXT] & E1000_CTRL_EXT_IAME)) {
         core->mac[IMS] &= ~effective_eiac;
@@ -2130,33 +2118,17 @@ e1000e_fix_icr_asserted(E1000ECore *core)
     trace_e1000e_irq_fix_icr_asserted(core->mac[ICR]);
 }
 
-static void
-e1000e_send_msi(E1000ECore *core, bool msix)
+static void e1000e_raise_interrupts(E1000ECore *core,
+                                    size_t index, uint32_t causes)
 {
-    uint32_t causes = core->mac[ICR] & core->mac[IMS] & ~E1000_ICR_ASSERTED;
-
-    core->msi_causes_pending &= causes;
-    causes ^= core->msi_causes_pending;
-    if (causes == 0) {
-        return;
-    }
-    core->msi_causes_pending |= causes;
+    bool is_msix = msix_enabled(core->owner);
+    uint32_t old_causes = core->mac[IMS] & core->mac[ICR];
+    uint32_t raised_causes;
 
-    if (msix) {
-        e1000e_msix_notify(core, causes);
-    } else {
-        if (!e1000e_itr_should_postpone(core)) {
-            trace_e1000e_irq_msi_notify(causes);
-            msi_notify(core->owner, 0);
-        }
-    }
-}
+    trace_e1000e_irq_set(index << 2,
+                         core->mac[index], core->mac[index] | causes);
 
-static void
-e1000e_update_interrupt_state(E1000ECore *core)
-{
-    bool interrupts_pending;
-    bool is_msix = msix_enabled(core->owner);
+    core->mac[index] |= causes;
 
     /* Set ICR[OTHER] for MSI-X */
     if (is_msix) {
@@ -2178,40 +2150,58 @@ e1000e_update_interrupt_state(E1000ECore *core)
      */
     core->mac[ICS] = core->mac[ICR];
 
-    interrupts_pending = (core->mac[IMS] & core->mac[ICR]) ? true : false;
-    if (!interrupts_pending) {
-        core->msi_causes_pending = 0;
-    }
-
     trace_e1000e_irq_pending_interrupts(core->mac[ICR] & core->mac[IMS],
                                         core->mac[ICR], core->mac[IMS]);
 
-    if (is_msix || msi_enabled(core->owner)) {
-        if (interrupts_pending) {
-            e1000e_send_msi(core, is_msix);
-        }
-    } else {
-        if (interrupts_pending) {
-            if (!e1000e_itr_should_postpone(core)) {
-                e1000e_raise_legacy_irq(core);
-            }
+    raised_causes = core->mac[IMS] & core->mac[ICR] & ~old_causes;
+    if (!raised_causes) {
+        return;
+    }
+
+    if (is_msix) {
+        e1000e_msix_notify(core, raised_causes & ~E1000_ICR_ASSERTED);
+    } else if (!e1000e_itr_should_postpone(core)) {
+        if (msi_enabled(core->owner)) {
+            trace_e1000e_irq_msi_notify(raised_causes);
+            msi_notify(core->owner, 0);
         } else {
-            e1000e_lower_legacy_irq(core);
+            e1000e_raise_legacy_irq(core);
         }
     }
 }
 
-static void
-e1000e_set_interrupt_cause(E1000ECore *core, uint32_t val)
+static void e1000e_lower_interrupts(E1000ECore *core,
+                                    size_t index, uint32_t causes)
 {
-    trace_e1000e_irq_set_cause_entry(val, core->mac[ICR]);
+    trace_e1000e_irq_clear(index << 2,
+                           core->mac[index], core->mac[index] & ~causes);
 
-    val |= e1000e_intmgr_collect_delayed_causes(core);
-    core->mac[ICR] |= val;
+    core->mac[index] &= ~causes;
 
-    trace_e1000e_irq_set_cause_exit(val, core->mac[ICR]);
+    /*
+     * Make sure ICR and ICS registers have the same value.
+     * The spec says that the ICS register is write-only.  However in practice,
+     * on real hardware ICS is readable, and for reads it has the same value as
+     * ICR (except that ICS does not have the clear on read behaviour of ICR).
+     *
+     * The VxWorks PRO/1000 driver uses this behaviour.
+     */
+    core->mac[ICS] = core->mac[ICR];
+
+    trace_e1000e_irq_pending_interrupts(core->mac[ICR] & core->mac[IMS],
+                                        core->mac[ICR], core->mac[IMS]);
 
-    e1000e_update_interrupt_state(core);
+    if (!(core->mac[IMS] & core->mac[ICR]) &&
+        !msix_enabled(core->owner) && !msi_enabled(core->owner)) {
+        e1000e_lower_legacy_irq(core);
+    }
+}
+
+static void
+e1000e_set_interrupt_cause(E1000ECore *core, uint32_t val)
+{
+    val |= e1000e_intmgr_collect_delayed_causes(core);
+    e1000e_raise_interrupts(core, ICR, val);
 }
 
 static inline void
@@ -2477,30 +2467,27 @@ e1000e_set_ics(E1000ECore *core, int index, uint32_t 
val)
 static void
 e1000e_set_icr(E1000ECore *core, int index, uint32_t val)
 {
-    uint32_t icr = 0;
     if ((core->mac[ICR] & E1000_ICR_ASSERTED) &&
         (core->mac[CTRL_EXT] & E1000_CTRL_EXT_IAME)) {
         trace_e1000e_irq_icr_process_iame();
-        e1000e_clear_ims_bits(core, core->mac[IAM]);
+        e1000e_lower_interrupts(core, IMS, core->mac[IAM]);
     }
 
-    icr = core->mac[ICR] & ~val;
     /*
      * Windows driver expects that the "receive overrun" bit and other
      * ones to be cleared when the "Other" bit (#24) is cleared.
      */
-    icr = (val & E1000_ICR_OTHER) ? (icr & ~E1000_ICR_OTHER_CAUSES) : icr;
-    trace_e1000e_irq_icr_write(val, core->mac[ICR], icr);
-    core->mac[ICR] = icr;
-    e1000e_update_interrupt_state(core);
+    if (val & E1000_ICR_OTHER) {
+        val |= E1000_ICR_OTHER_CAUSES;
+    }
+    e1000e_lower_interrupts(core, ICR, val);
 }
 
 static void
 e1000e_set_imc(E1000ECore *core, int index, uint32_t val)
 {
     trace_e1000e_irq_ims_clear_set_imc(val);
-    e1000e_clear_ims_bits(core, val);
-    e1000e_update_interrupt_state(core);
+    e1000e_lower_interrupts(core, IMS, val);
 }
 
 static void
@@ -2521,9 +2508,6 @@ e1000e_set_ims(E1000ECore *core, int index, uint32_t val)
 
     uint32_t valid_val = val & ims_valid_mask;
 
-    trace_e1000e_irq_set_ims(val, core->mac[IMS], core->mac[IMS] | valid_val);
-    core->mac[IMS] |= valid_val;
-
     if ((valid_val & ims_ext_mask) &&
         (core->mac[CTRL_EXT] & E1000_CTRL_EXT_PBA_CLR) &&
         msix_enabled(core->owner)) {
@@ -2536,7 +2520,7 @@ e1000e_set_ims(E1000ECore *core, int index, uint32_t val)
         e1000e_intrmgr_fire_all_timers(core);
     }
 
-    e1000e_update_interrupt_state(core);
+    e1000e_raise_interrupts(core, IMS, valid_val);
 }
 
 static void
@@ -2609,28 +2593,25 @@ static uint32_t
 e1000e_mac_icr_read(E1000ECore *core, int index)
 {
     uint32_t ret = core->mac[ICR];
-    trace_e1000e_irq_icr_read_entry(ret);
 
     if (core->mac[IMS] == 0) {
         trace_e1000e_irq_icr_clear_zero_ims();
-        core->mac[ICR] = 0;
+        e1000e_lower_interrupts(core, ICR, 0xffffffff);
     }
 
     if (!msix_enabled(core->owner)) {
         trace_e1000e_irq_icr_clear_nonmsix_icr_read();
-        core->mac[ICR] = 0;
+        e1000e_lower_interrupts(core, ICR, 0xffffffff);
     }
 
     if ((core->mac[ICR] & E1000_ICR_ASSERTED) &&
         (core->mac[CTRL_EXT] & E1000_CTRL_EXT_IAME)) {
         trace_e1000e_irq_icr_clear_iame();
-        core->mac[ICR] = 0;
+        e1000e_lower_interrupts(core, ICR, 0xffffffff);
         trace_e1000e_irq_icr_process_iame();
-        e1000e_clear_ims_bits(core, core->mac[IAM]);
+        e1000e_lower_interrupts(core, IMS, core->mac[IAM]);
     }
 
-    trace_e1000e_irq_icr_read_exit(core->mac[ICR]);
-    e1000e_update_interrupt_state(core);
     return ret;
 }
 
diff --git a/hw/net/trace-events b/hw/net/trace-events
index 64d776bc2a..d171dc8179 100644
--- a/hw/net/trace-events
+++ b/hw/net/trace-events
@@ -205,6 +205,8 @@ e1000e_irq_msix_notify_postponed_vec(int idx) "Sending 
MSI-X postponed by EITR[%
 e1000e_irq_legacy_notify(bool level) "IRQ line state: %d"
 e1000e_irq_msix_notify_vec(uint32_t vector) "MSI-X notify vector 0x%x"
 e1000e_irq_postponed_by_xitr(uint32_t reg) "Interrupt postponed by [E]ITR 
register 0x%x"
+e1000e_irq_clear(uint32_t offset, uint32_t old, uint32_t new) "Clearing 
interrupt register 0x%x: 0x%x --> 0x%x"
+e1000e_irq_set(uint32_t offset, uint32_t old, uint32_t new) "Setting interrupt 
register 0x%x: 0x%x --> 0x%x"
 e1000e_irq_clear_ims(uint32_t bits, uint32_t old_ims, uint32_t new_ims) 
"Clearing IMS bits 0x%x: 0x%x --> 0x%x"
 e1000e_irq_set_ims(uint32_t bits, uint32_t old_ims, uint32_t new_ims) "Setting 
IMS bits 0x%x: 0x%x --> 0x%x"
 e1000e_irq_fix_icr_asserted(uint32_t new_val) "ICR_ASSERTED bit fixed: 0x%x"
-- 
2.40.0




reply via email to

[Prev in Thread] Current Thread [Next in Thread]