[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[PATCH] virtio-net : Add check for VIRTIO_NET_F_MAC
From: |
Cindy Lu |
Subject: |
[PATCH] virtio-net : Add check for VIRTIO_NET_F_MAC |
Date: |
Wed, 29 Sep 2021 14:52:15 +0800 |
For vdpa device, if the host support VIRTIO_NET_F_MAC
we need to read the mac address from hardware, so need
to check this bit, the logic is
1 if the host support VIRTIO_NET_F_MAC and the mac address
is correct, qemu will use the mac address in hardware
2.if the host not support , qemu will use the mac from cmdline
3.if the cmdline not provide mac address, qemu will use radam mac
address
Signed-off-by: Cindy Lu <lulu@redhat.com>
---
hw/net/virtio-net.c | 34 +++++++++++++++++++++++++++-------
1 file changed, 27 insertions(+), 7 deletions(-)
diff --git a/hw/net/virtio-net.c b/hw/net/virtio-net.c
index 55aac06a0a..085daa28b0 100644
--- a/hw/net/virtio-net.c
+++ b/hw/net/virtio-net.c
@@ -127,9 +127,9 @@ static void virtio_net_get_config(VirtIODevice *vdev,
uint8_t *config)
struct virtio_net_config netcfg;
NetClientState *nc = qemu_get_queue(n->nic);
static const MACAddr zero = { .a = { 0, 0, 0, 0, 0, 0 } };
-
int ret = 0;
- memset(&netcfg, 0 , sizeof(struct virtio_net_config));
+
+ memset(&netcfg, 0, sizeof(struct virtio_net_config));
virtio_stw_p(vdev, &netcfg.status, n->status);
virtio_stw_p(vdev, &netcfg.max_virtqueue_pairs, n->max_queues);
virtio_stw_p(vdev, &netcfg.mtu, n->net_conf.mtu);
@@ -159,12 +159,21 @@ static void virtio_net_get_config(VirtIODevice *vdev,
uint8_t *config)
* address has been configured correctly elsewhere - just not
* reported by the device.
*/
+
if (memcmp(&netcfg.mac, &zero, sizeof(zero)) == 0) {
info_report("Zero hardware mac address detected. Ignoring.");
memcpy(netcfg.mac, n->mac, ETH_ALEN);
}
- memcpy(config, &netcfg, n->config_size);
+ /*
+ * If the host support VIRTIO_NET_F_MAC, That means hardware
+ * will provide the mac address, otherwise we don't need to use it.
+ * use the mac address from qemu cfg
+ */
+ if (!(virtio_host_has_feature(vdev, VIRTIO_NET_F_MAC))) {
+ memcpy(netcfg.mac, n->mac, ETH_ALEN);
+ }
}
+ memcpy(config, &netcfg, n->config_size);
}
}
@@ -3453,11 +3462,22 @@ static void virtio_net_device_realize(DeviceState *dev,
Error **errp)
nc = qemu_get_queue(n->nic);
nc->rxfilter_notify_enabled = 1;
- if (nc->peer && nc->peer->info->type == NET_CLIENT_DRIVER_VHOST_VDPA) {
+ if (nc->peer && nc->peer->info->type == NET_CLIENT_DRIVER_VHOST_VDPA) {
+
struct virtio_net_config netcfg = {};
- memcpy(&netcfg.mac, &n->nic_conf.macaddr, ETH_ALEN);
- vhost_net_set_config(get_vhost_net(nc->peer),
- (uint8_t *)&netcfg, 0, ETH_ALEN, VHOST_SET_CONFIG_TYPE_MASTER);
+ /*
+ * get the real mac address from hardware or qemu cmline
+ *
+ * If the host support VIRTIO_NET_F_MAC, That means hardware
+ * will provide the mac address, otherwise we don't need to use it.
+ * use the mac address from qemu cfg
+ */
+ virtio_net_get_config(vdev, (uint8_t *)&netcfg);
+ /*
+ * for vdpa device qemu need to set the real mac back to hardware
+ */
+ vhost_net_set_config(get_vhost_net(nc->peer), (uint8_t *)&netcfg, 0,
+ ETH_ALEN, VHOST_SET_CONFIG_TYPE_MASTER);
}
QTAILQ_INIT(&n->rsc_chains);
n->qdev = dev;
--
2.21.3
- [PATCH] virtio-net : Add check for VIRTIO_NET_F_MAC,
Cindy Lu <=