RE: [PATCH v5 0/4] hw/block/m25p80: Numonyx: Fix dummy cycles and check for SPI mode on cmds

[Joe Komlodi]

Hi Peter,

This series has been reviewed, but it looks like it slipped through the cracks.
Is it possible it could be merged through your tree, assuming it looks good?

Thanks!
Joe

-----Original Message-----
From: Qemu-devel <qemu-devel-bounces+komlodi=xilinx.com@nongnu.org> On Behalf 
Of Joe Komlodi
Sent: Monday, November 16, 2020 3:11 PM
To: qemu-devel@nongnu.org
Cc: Francisco Eduardo Iglesias <figlesia@xilinx.com>; alistair@alistair23.me; 
philippe.mathieu.daude@gmail.com; qemu-block@nongnu.org; mreitz@redhat.com
Subject: [PATCH v5 0/4] hw/block/m25p80: Numonyx: Fix dummy cycles and check 
for SPI mode on cmds

Changelog:
v4 -> v5
 - 3/4: Simplify logic when changing state and checking mode.
 - 3/4: numonyx_get_mode -> numonyx_mode
 - 4/4: Reword commit message to include QIO mode.

v3 -> v4
 - 1/4: Patch changed to change names of register fields to be more accurate.
 - 1/4: Revert polarity change from v3.
 - 2/4: Added, fixes polarity of VCFG XIP mode when copied from NVCFG.
 - 3/4: Removed check_cmd_mode function, each command check is done in 
decode_new_cmd instead.
 - 3/4: Add guest error print if JEDEC read is executed in QIO or DIO mode.
 - 3/4: Don't check PP and PP4, they work regardless of mode. PP4_4 is left as 
is.
 - 3/4: Simplify get_mode function.
 - 4/4: Simplify extract_cfg_num_dummies function.
 - 4/4: Use switch statement instead of table for cycle retrieving.

v2 -> v3
 - 1/3: Added, Fixes NVCFG polarity for DIO/QIO.
 - 2/3: Added, Checks if we can execute the current command in standard/DIO/QIO 
mode.
 - 3/3: Was 1/1 in v2.  Added cycle counts for DIO/QIO mode.

v1 -> v2
 - 1/2: Change function name to be more accurate
 - 2/2: Dropped

Hi all,

The series fixes the behavior of the dummy cycle register for Numonyx flashes 
so it's closer to how hardware behaves.
It also checks if a command can be executed in the current SPI mode (standard, 
DIO, or QIO) before extracting dummy cycles for the command.

On hardware, the dummy cycles for fast read commands are set to a specific value
(8 or 10) if the register is all 0s or 1s.
If the register value isn't all 0s or 1s, then the flash expects the amount of 
cycles sent to be equal to the count in the register.

Thanks!
Joe

Joe Komlodi (4):
  hw/block/m25p80: Make Numonyx config field names more accurate
  hw/block/m25p80: Fix when VCFG XIP bit is set for Numonyx
  hw/block/m25p80: Check SPI mode before running some Numonyx commands
  hw/block/m25p80: Fix Numonyx fast read dummy cycle count

 hw/block/m25p80.c | 158 ++++++++++++++++++++++++++++++++++++++++++++----------
 1 file changed, 129 insertions(+), 29 deletions(-)

--
2.7.4