[PULL 5/6] hw/m68k/mcf5206: Replace remaining hw_error()s by qemu_log_mask()

[Thomas Huth]

From: Thomas Huth <huth@tuxfamily.org>

hw_error() dumps the CPU state and exits QEMU. This is ok during initial
code development (to see where the guest code is currently executing),
but it is certainly not the desired behavior that we want to present to
normal users, and it can also cause trouble when e.g. fuzzing devices.
Thus let's replace these hw_error()s by qemu_log_mask()s instead.

Message-Id: <20200611055807.15921-1-huth@tuxfamily.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@tuxfamily.org>
---
 hw/m68k/mcf5206.c | 39 ++++++++++++++++++++++++++++-----------
 1 file changed, 28 insertions(+), 11 deletions(-)

diff --git a/hw/m68k/mcf5206.c b/hw/m68k/mcf5206.c
index a2fef04f8e..94a37a1a46 100644
--- a/hw/m68k/mcf5206.c
+++ b/hw/m68k/mcf5206.c
@@ -10,7 +10,6 @@
 #include "qemu/error-report.h"
 #include "qemu/log.h"
 #include "cpu.h"
-#include "hw/hw.h"
 #include "hw/irq.h"
 #include "hw/m68k/mcf.h"
 #include "qemu/timer.h"
@@ -69,10 +68,16 @@ static void m5206_timer_recalibrate(m5206_timer_state *s)
     if (mode == 2)
         prescale *= 16;
 
-    if (mode == 3 || mode == 0)
-        hw_error("m5206_timer: mode %d not implemented\n", mode);
-    if ((s->tmr & TMR_FRR) == 0)
-        hw_error("m5206_timer: free running mode not implemented\n");
+    if (mode == 3 || mode == 0) {
+        qemu_log_mask(LOG_UNIMP, "m5206_timer: mode %d not implemented\n",
+                      mode);
+        goto exit;
+    }
+    if ((s->tmr & TMR_FRR) == 0) {
+        qemu_log_mask(LOG_UNIMP,
+                      "m5206_timer: free running mode not implemented\n");
+        goto exit;
+    }
 
     /* Assume 66MHz system clock.  */
     ptimer_set_freq(s->timer, 66000000 / prescale);
@@ -391,7 +396,9 @@ static uint32_t m5206_mbar_readb(void *opaque, hwaddr 
offset)
     m5206_mbar_state *s = (m5206_mbar_state *)opaque;
     offset &= 0x3ff;
     if (offset >= 0x200) {
-        hw_error("Bad MBAR read offset 0x%x", (int)offset);
+        qemu_log_mask(LOG_GUEST_ERROR, "Bad MBAR read offset 0x%" HWADDR_PRIX,
+                      offset);
+        return 0;
     }
     if (m5206_mbar_width[offset >> 2] > 1) {
         uint16_t val;
@@ -410,7 +417,9 @@ static uint32_t m5206_mbar_readw(void *opaque, hwaddr 
offset)
     int width;
     offset &= 0x3ff;
     if (offset >= 0x200) {
-        hw_error("Bad MBAR read offset 0x%x", (int)offset);
+        qemu_log_mask(LOG_GUEST_ERROR, "Bad MBAR read offset 0x%" HWADDR_PRIX,
+                      offset);
+        return 0;
     }
     width = m5206_mbar_width[offset >> 2];
     if (width > 2) {
@@ -434,7 +443,9 @@ static uint32_t m5206_mbar_readl(void *opaque, hwaddr 
offset)
     int width;
     offset &= 0x3ff;
     if (offset >= 0x200) {
-        hw_error("Bad MBAR read offset 0x%x", (int)offset);
+        qemu_log_mask(LOG_GUEST_ERROR, "Bad MBAR read offset 0x%" HWADDR_PRIX,
+                      offset);
+        return 0;
     }
     width = m5206_mbar_width[offset >> 2];
     if (width < 4) {
@@ -458,7 +469,9 @@ static void m5206_mbar_writeb(void *opaque, hwaddr offset,
     int width;
     offset &= 0x3ff;
     if (offset >= 0x200) {
-        hw_error("Bad MBAR write offset 0x%x", (int)offset);
+        qemu_log_mask(LOG_GUEST_ERROR, "Bad MBAR write offset 0x%" HWADDR_PRIX,
+                      offset);
+        return;
     }
     width = m5206_mbar_width[offset >> 2];
     if (width > 1) {
@@ -482,7 +495,9 @@ static void m5206_mbar_writew(void *opaque, hwaddr offset,
     int width;
     offset &= 0x3ff;
     if (offset >= 0x200) {
-        hw_error("Bad MBAR write offset 0x%x", (int)offset);
+        qemu_log_mask(LOG_GUEST_ERROR, "Bad MBAR write offset 0x%" HWADDR_PRIX,
+                      offset);
+        return;
     }
     width = m5206_mbar_width[offset >> 2];
     if (width > 2) {
@@ -510,7 +525,9 @@ static void m5206_mbar_writel(void *opaque, hwaddr offset,
     int width;
     offset &= 0x3ff;
     if (offset >= 0x200) {
-        hw_error("Bad MBAR write offset 0x%x", (int)offset);
+        qemu_log_mask(LOG_GUEST_ERROR, "Bad MBAR write offset 0x%" HWADDR_PRIX,
+                      offset);
+        return;
     }
     width = m5206_mbar_width[offset >> 2];
     if (width < 4) {
-- 
2.18.1