qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[PULL 3/3] docs: stop documenting the e1000 NIC model as the default


From: Daniel P . Berrangé
Subject: [PULL 3/3] docs: stop documenting the e1000 NIC model as the default
Date: Fri, 7 Feb 2020 12:24:40 +0000

The default NIC model for QEMU varies per machine type, and is liable to
change across machine type versions. Documenting e1000 NIC as the
default for PC/i386 is thus misleading to users at best. In particular
the PC q35 machine type switched to use e1000e, but only in machine
type versions after 2.11.

Rather than try to explain which NIC model is used for each machine
type version, remove mention of e1000 as the default, and steer users
towards always specifying their desired model.

Reviewed-by: Thomas Huth <address@hidden>
Reviewed by: Aleksandar Markovic <address@hidden>
Signed-off-by: Daniel P. Berrangé <address@hidden>
---
 qemu-options.hx | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/qemu-options.hx b/qemu-options.hx
index ff3e806977..ac315c1ac4 100644
--- a/qemu-options.hx
+++ b/qemu-options.hx
@@ -2428,8 +2428,7 @@ Use @option{model=help} to list the available device 
types.
 The hardware MAC address can be set with @option{mac=@var{macaddr}}.
 
 The following two example do exactly the same, to show how @option{-nic} can
-be used to shorten the command line length (note that the e1000 is the default
-on i386, so the @option{model=e1000} parameter could even be omitted here, 
too):
+be used to shorten the command line length:
 @example
 @value{qemu_system} -netdev user,id=n1,ipv6=off -device 
e1000,netdev=n1,mac=52:54:98:76:54:32
 @value{qemu_system} -nic user,ipv6=off,model=e1000,mac=52:54:98:76:54:32
@@ -2843,9 +2842,12 @@ netdev with ID @var{nd} by using the 
@option{netdev=@var{nd}} option.
 Legacy option to configure or create an on-board (or machine default) Network
 Interface Card(NIC) and connect it either to the emulated hub with ID 0 (i.e.
 the default hub), or to the netdev @var{nd}.
-The NIC is an e1000 by default on the PC target. Optionally, the MAC address
-can be changed to @var{mac}, the device address set to @var{addr} (PCI cards
-only), and a @var{name} can be assigned for use in monitor commands.
+If @var{model} is omitted, then the default NIC model associated with
+the machine type is used. Note that the default NIC model may change in
+future QEMU releases, so it is highly recommended to always specify a model.
+Optionally, the MAC address can be changed to @var{mac}, the device
+address set to @var{addr} (PCI cards only), and a @var{name} can be
+assigned for use in monitor commands.
 Optionally, for PCI cards, you can specify the number @var{v} of MSI-X vectors
 that the card should have; this option currently only affects virtio cards; set
 @var{v} = 0 to disable MSI-X. If no @option{-net} option is specified, a single
-- 
2.24.1




reply via email to

[Prev in Thread] Current Thread [Next in Thread]