[PULL 01/10] hw/arm/nseries: Replace the bluetooth chardev with a "null" chardev

[Thomas Huth]

We are going to remove the bitrotten bluetooth backend, so we can
not use it in the n800 and n810 machines anymore. Replace the chardev
here with a "null" chardev and stop including the "hw/bt.h" header.

I am not aware of a full working N8x0 environment that can be used to
test these machines, but the Linux kernel from the Meego project that
can be found on http://stskeeps.subnetmask.net/meego-n8x0/ still seems
to boot as far as it did before.

Message-Id: <address@hidden>
Reviewed-by: Peter Maydell <address@hidden>
Acked-by: Paolo Bonzini <address@hidden>
Signed-off-by: Thomas Huth <address@hidden>
---
 hw/arm/nseries.c | 16 +++++++---------
 qemu-doc.texi    |  2 --
 2 files changed, 7 insertions(+), 11 deletions(-)

diff --git a/hw/arm/nseries.c b/hw/arm/nseries.c
index 7e361936a9..3fd196fb30 100644
--- a/hw/arm/nseries.c
+++ b/hw/arm/nseries.c
@@ -21,6 +21,7 @@
 #include "qemu/osdep.h"
 #include "qapi/error.h"
 #include "cpu.h"
+#include "chardev/char.h"
 #include "qemu/cutils.h"
 #include "qemu/bswap.h"
 #include "sysemu/reset.h"
@@ -39,7 +40,6 @@
 #include "hw/qdev-properties.h"
 #include "hw/block/flash.h"
 #include "hw/hw.h"
-#include "hw/bt.h"
 #include "hw/loader.h"
 #include "hw/sysbus.h"
 #include "qemu/log.h"
@@ -792,13 +792,11 @@ static void n8x0_cbus_setup(struct n800_s *s)
 
 static void n8x0_uart_setup(struct n800_s *s)
 {
-    Chardev *radio = uart_hci_init();
-
-    qdev_connect_gpio_out(s->mpu->gpio, N8X0_BT_RESET_GPIO,
-                    csrhci_pins_get(radio)[csrhci_pin_reset]);
-    qdev_connect_gpio_out(s->mpu->gpio, N8X0_BT_WKUP_GPIO,
-                    csrhci_pins_get(radio)[csrhci_pin_wakeup]);
-
+    Chardev *radio = qemu_chr_new("bt-dummy-uart", "null", NULL);
+    /*
+     * Note: We used to connect N8X0_BT_RESET_GPIO and N8X0_BT_WKUP_GPIO
+     * here, but this code has been removed with the bluetooth backend.
+     */
     omap_uart_attach(s->mpu->uart[BT_UART], radio);
 }
 
@@ -1137,7 +1135,7 @@ static struct omap_partition_info_s {
     { 0, 0, 0, NULL }
 };
 
-static bdaddr_t n8x0_bd_addr = {{ N8X0_BD_ADDR }};
+static uint8_t n8x0_bd_addr[6] = { N8X0_BD_ADDR };
 
 static int n8x0_atag_setup(void *p, int model)
 {
diff --git a/qemu-doc.texi b/qemu-doc.texi
index 3ddf5c0a68..ed3df01dac 100644
--- a/qemu-doc.texi
+++ b/qemu-doc.texi
@@ -2308,8 +2308,6 @@ Secure Digital card connected to OMAP MMC/SD host
 @item
 Three OMAP on-chip UARTs and on-chip STI debugging console
 @item
-A Bluetooth(R) transceiver and HCI connected to an UART
-@item
 Mentor Graphics "Inventra" dual-role USB controller embedded in a TI
 TUSB6010 chip - only USB host mode is supported
 @item
-- 
2.18.1