Re: [PATCH v6] ssi: xilinx_spips: Skip spi bus update for a few register writes

[Edgar E. Iglesias]

On Fri, Nov 15, 2019 at 08:41:45PM +0530, Sai Pavan Boddu wrote:
> A few configuration register writes need not update the spi bus state, so just
> return after the register write.
> 
> Signed-off-by: Sai Pavan Boddu <address@hidden>
> Reviewed-by: Alistair Francis <address@hidden>
> Reviewed-by: Francisco Iglesias <address@hidden>
> Tested-by: Francisco Iglesias <address@hidden>


Reviewed-by: Edgar E. Iglesias <address@hidden>


> ---
> 
> Changes for V2:
>       Just skip update of spips cs and fifos
>       Update commit message accordingly
> Changes for V4:
>       Avoid checking for zynqmp qspi
>       Skip spi bus update for few of the registers Changes for V4:
>       Move the register list to existing switch case above.
> Changes for V5:
>       Fixed Commit message.
> Changes for V6:
>       Fixed commit message. Added Review tags.
> 
> Note: Resending this as it got filtered for first two attempts.
> 
> 
>  hw/ssi/xilinx_spips.c | 22 ++++++++++++++++++----
>  1 file changed, 18 insertions(+), 4 deletions(-)
> 
> diff --git a/hw/ssi/xilinx_spips.c b/hw/ssi/xilinx_spips.c
> index a309c71..0d6c2e1 100644
> --- a/hw/ssi/xilinx_spips.c
> +++ b/hw/ssi/xilinx_spips.c
> @@ -109,6 +109,7 @@
>  #define R_GPIO              (0x30 / 4)
>  #define R_LPBK_DLY_ADJ      (0x38 / 4)
>  #define R_LPBK_DLY_ADJ_RESET (0x33)
> +#define R_IOU_TAPDLY_BYPASS (0x3C / 4)
>  #define R_TXD1              (0x80 / 4)
>  #define R_TXD2              (0x84 / 4)
>  #define R_TXD3              (0x88 / 4)
> @@ -139,6 +140,8 @@
>  #define R_LQSPI_STS         (0xA4 / 4)
>  #define LQSPI_STS_WR_RECVD      (1 << 1)
>  
> +#define R_DUMMY_CYCLE_EN    (0xC8 / 4)
> +#define R_ECO               (0xF8 / 4)
>  #define R_MOD_ID            (0xFC / 4)
>  
>  #define R_GQSPI_SELECT          (0x144 / 4)
> @@ -970,6 +973,7 @@ static void xilinx_spips_write(void *opaque, hwaddr addr,
>  {
>      int mask = ~0;
>      XilinxSPIPS *s = opaque;
> +    bool try_flush = true;
>  
>      DB_PRINT_L(0, "addr=" TARGET_FMT_plx " = %x\n", addr, (unsigned)value);
>      addr >>= 2;
> @@ -1019,13 +1023,23 @@ static void xilinx_spips_write(void *opaque, hwaddr 
> addr,
>          tx_data_bytes(&s->tx_fifo, (uint32_t)value, 3,
>                        s->regs[R_CONFIG] & R_CONFIG_ENDIAN);
>          goto no_reg_update;
> +    /* Skip SPI bus update for below registers writes */
> +    case R_GPIO:
> +    case R_LPBK_DLY_ADJ:
> +    case R_IOU_TAPDLY_BYPASS:
> +    case R_DUMMY_CYCLE_EN:
> +    case R_ECO:
> +        try_flush = false;
> +        break;
>      }
>      s->regs[addr] = (s->regs[addr] & ~mask) | (value & mask);
>  no_reg_update:
> -    xilinx_spips_update_cs_lines(s);
> -    xilinx_spips_check_flush(s);
> -    xilinx_spips_update_cs_lines(s);
> -    xilinx_spips_update_ixr(s);
> +    if (try_flush) {
> +        xilinx_spips_update_cs_lines(s);
> +        xilinx_spips_check_flush(s);
> +        xilinx_spips_update_cs_lines(s);
> +        xilinx_spips_update_ixr(s);
> +    }
>  }
>  
>  static const MemoryRegionOps spips_ops = {
> -- 
> 2.7.4
>