Re: [PATCH 04/19] hw/arm/bcm2835: Rename some definitions

[Alistair Francis]

On Thu, Sep 26, 2019 at 10:40 AM Philippe Mathieu-Daudé <address@hidden> wrote:
>
> The UART1 is part of the AUX peripheral,
> the PCM_CLOCK (yet unimplemented) is part of the CPRMAN.
>
> Reviewed-by: Peter Maydell <address@hidden>
> Signed-off-by: Philippe Mathieu-Daudé <address@hidden>

Reviewed-by: Alistair Francis <address@hidden>

Alistair

> ---
> I dunno if this is OK to do that since the header has:
>
>  * These definitions are derived from those in Raspbian Linux at
>  * arch/arm/mach-{bcm2708,bcm2709}/include/mach/platform.h
>  * where they carry the following notice:
>  *
>  * Copyright (C) 2010 Broadcom
> ---
>  hw/arm/bcm2835_peripherals.c    |  7 ++++---
>  hw/arm/bcm2836.c                |  2 +-
>  include/hw/arm/raspi_platform.h | 16 +++++++---------
>  3 files changed, 12 insertions(+), 13 deletions(-)
>
> diff --git a/hw/arm/bcm2835_peripherals.c b/hw/arm/bcm2835_peripherals.c
> index 8984e2e91f..1bd2ff41d5 100644
> --- a/hw/arm/bcm2835_peripherals.c
> +++ b/hw/arm/bcm2835_peripherals.c
> @@ -165,7 +165,8 @@ static void bcm2835_peripherals_realize(DeviceState *dev, 
> Error **errp)
>                  sysbus_mmio_get_region(SYS_BUS_DEVICE(&s->uart0), 0));
>      sysbus_connect_irq(SYS_BUS_DEVICE(&s->uart0), 0,
>          qdev_get_gpio_in_named(DEVICE(&s->ic), BCM2835_IC_GPU_IRQ,
> -                               INTERRUPT_UART));
> +                               INTERRUPT_UART0));
> +
>      /* AUX / UART1 */
>      qdev_prop_set_chr(DEVICE(&s->aux), "chardev", serial_hd(1));
>
> @@ -175,7 +176,7 @@ static void bcm2835_peripherals_realize(DeviceState *dev, 
> Error **errp)
>          return;
>      }
>
> -    memory_region_add_subregion(&s->peri_mr, UART1_OFFSET,
> +    memory_region_add_subregion(&s->peri_mr, AUX_OFFSET,
>                  sysbus_mmio_get_region(SYS_BUS_DEVICE(&s->aux), 0));
>      sysbus_connect_irq(SYS_BUS_DEVICE(&s->aux), 0,
>          qdev_get_gpio_in_named(DEVICE(&s->ic), BCM2835_IC_GPU_IRQ,
> @@ -268,7 +269,7 @@ static void bcm2835_peripherals_realize(DeviceState *dev, 
> Error **errp)
>          return;
>      }
>
> -    memory_region_add_subregion(&s->peri_mr, EMMC_OFFSET,
> +    memory_region_add_subregion(&s->peri_mr, EMMC1_OFFSET,
>                  sysbus_mmio_get_region(SYS_BUS_DEVICE(&s->sdhci), 0));
>      sysbus_connect_irq(SYS_BUS_DEVICE(&s->sdhci), 0,
>          qdev_get_gpio_in_named(DEVICE(&s->ic), BCM2835_IC_GPU_IRQ,
> diff --git a/hw/arm/bcm2836.c b/hw/arm/bcm2836.c
> index 493a913f89..723aef6bf5 100644
> --- a/hw/arm/bcm2836.c
> +++ b/hw/arm/bcm2836.c
> @@ -126,7 +126,7 @@ static void bcm2836_realize(DeviceState *dev, Error 
> **errp)
>
>          /* set periphbase/CBAR value for CPU-local registers */
>          object_property_set_int(OBJECT(&s->cpus[n]),
> -                                BCM2836_PERI_BASE + MCORE_OFFSET,
> +                                BCM2836_PERI_BASE + MSYNC_OFFSET,
>                                  "reset-cbar", &err);
>          if (err) {
>              error_propagate(errp, err);
> diff --git a/include/hw/arm/raspi_platform.h b/include/hw/arm/raspi_platform.h
> index 10083d33df..66969fac5d 100644
> --- a/include/hw/arm/raspi_platform.h
> +++ b/include/hw/arm/raspi_platform.h
> @@ -25,8 +25,7 @@
>  #ifndef HW_ARM_RASPI_PLATFORM_H
>  #define HW_ARM_RASPI_PLATFORM_H
>
> -#define MCORE_OFFSET            0x0000   /* Fake frame buffer device
> -                                          * (the multicore sync block) */
> +#define MSYNC_OFFSET            0x0000   /* Multicore Sync Block */
>  #define IC0_OFFSET              0x2000
>  #define ST_OFFSET               0x3000   /* System Timer */
>  #define MPHI_OFFSET             0x6000   /* Message-based Parallel Host 
> Intf. */
> @@ -37,9 +36,8 @@
>  #define ARMCTRL_TIMER0_1_OFFSET (ARM_OFFSET + 0x400) /* Timer 0 and 1 */
>  #define ARMCTRL_0_SBM_OFFSET    (ARM_OFFSET + 0x800) /* User 0 (ARM) 
> Semaphores
>                                                        * Doorbells & 
> Mailboxes */
> -#define PM_OFFSET               0x100000 /* Power Management, Reset 
> controller
> -                                          * and Watchdog registers */
> -#define PCM_CLOCK_OFFSET        0x101098
> +#define CPRMAN_OFFSET           0x100000 /* Power Management, Watchdog */
> +#define CM_OFFSET               0x101000 /* Clock Management */
>  #define RNG_OFFSET              0x104000
>  #define GPIO_OFFSET             0x200000
>  #define UART0_OFFSET            0x201000
> @@ -47,11 +45,11 @@
>  #define I2S_OFFSET              0x203000
>  #define SPI0_OFFSET             0x204000
>  #define BSC0_OFFSET             0x205000 /* BSC0 I2C/TWI */
> -#define UART1_OFFSET            0x215000
> -#define EMMC_OFFSET             0x300000
> +#define AUX_OFFSET              0x215000 /* AUX: UART1/SPI1/SPI2 */
> +#define EMMC1_OFFSET            0x300000
>  #define SMI_OFFSET              0x600000
>  #define BSC1_OFFSET             0x804000 /* BSC1 I2C/TWI */
> -#define USB_OFFSET              0x980000 /* DTC_OTG USB controller */
> +#define USB_OTG_OFFSET          0x980000 /* DTC_OTG USB controller */
>  #define DMA15_OFFSET            0xE05000 /* DMA controller, channel 15 */
>
>  /* GPU interrupts */
> @@ -112,7 +110,7 @@
>  #define INTERRUPT_SPI                  54
>  #define INTERRUPT_I2SPCM               55
>  #define INTERRUPT_SDIO                 56
> -#define INTERRUPT_UART                 57
> +#define INTERRUPT_UART0                57
>  #define INTERRUPT_SLIMBUS              58
>  #define INTERRUPT_VEC                  59
>  #define INTERRUPT_CPG                  60
> --
> 2.20.1
>
>