qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Qemu-devel] [PATCH v5 2/5] hw/block/pflash_cfi01: Use the correct READ_


From: Philippe Mathieu-Daudé
Subject: [Qemu-devel] [PATCH v5 2/5] hw/block/pflash_cfi01: Use the correct READ_ARRAY value
Date: Mon, 15 Jul 2019 14:13:35 +0200

In the document [*] the "Read Array Flowchart", the READ_ARRAY
command has a value of 0xff.

Use the correct value in the pflash model.

There is no change of behavior in the guest, because:
- when the guest were sending 0xFF, the reset_flash label
  was setting the command value as 0x00
- 0x00 was used internally for READ_ARRAY

To keep migration with older versions behaving correctly, we
decide to always migrate the READ_ARRAY as 0x00.

If the CFI open standard decide to assign a new command of value
0x00, this model is flawed because it uses this value internally.
If a guest eventually requires this new CFI feature, a different
model will be required (or this same model but breaking backward
migration). So it is safe to keep migrating READ_ARRAY as 0x00.

[*] "Common Flash Interface (CFI) and Command Sets"
    (Intel Application Note 646)
    Appendix B "Basic Command Set"

Reviewed-by: John Snow <address@hidden>
Reviewed-by: Alistair Francis <address@hidden>
Regression-tested-by: Laszlo Ersek <address@hidden>
Signed-off-by: Philippe Mathieu-Daudé <address@hidden>
---
v3: Handle migrating the 'cmd' field.
v4: Handle migrating to older QEMU (Dave)
v5: Add a paragraph about why this model is flawed due to
    historically using READ_ARRAY as 0x00 (Dave, Peter).

Since Laszlo stated he did not test migration [*], I'm keeping his
test tag, because the change with v2 has no impact in the tests
he ran.

Likewise I'm keeping John and Alistair tags, but I'd like an extra
review for the migration change, thanks!

[*] https://lists.gnu.org/archive/html/qemu-devel/2019-07/msg00679.html
---
 hw/block/pflash_cfi01.c | 57 ++++++++++++++++++++++++++++++++++-------
 1 file changed, 48 insertions(+), 9 deletions(-)

diff --git a/hw/block/pflash_cfi01.c b/hw/block/pflash_cfi01.c
index 9e34fd4e82..85bb2132c0 100644
--- a/hw/block/pflash_cfi01.c
+++ b/hw/block/pflash_cfi01.c
@@ -96,6 +96,37 @@ struct PFlashCFI01 {
     bool old_multiple_chip_handling;
 };
 
+static int pflash_pre_save(void *opaque)
+{
+    PFlashCFI01 *s = opaque;
+
+    /*
+     * Previous to QEMU v4.1 an incorrect value of 0x00 was used for the
+     * READ_ARRAY command. To preserve migrating to these older version,
+     * always migrate the READ_ARRAY command as 0x00.
+     */
+    if (s->cmd == 0xff) {
+        s->cmd = 0x00;
+    }
+
+    return 0;
+}
+
+static int pflash_post_save(void *opaque)
+{
+    PFlashCFI01 *s = opaque;
+
+    /*
+     * If migration failed, the guest will continue to run.
+     * Restore the correct READ_ARRAY value.
+     */
+    if (s->cmd == 0x00) {
+        s->cmd = 0xff;
+    }
+
+    return 0;
+}
+
 static int pflash_post_load(void *opaque, int version_id);
 
 static const VMStateDescription vmstate_pflash = {
@@ -103,6 +134,8 @@ static const VMStateDescription vmstate_pflash = {
     .version_id = 1,
     .minimum_version_id = 1,
     .post_load = pflash_post_load,
+    .pre_save = pflash_pre_save,
+    .post_save = pflash_post_save,
     .fields = (VMStateField[]) {
         VMSTATE_UINT8(wcycle, PFlashCFI01),
         VMSTATE_UINT8(cmd, PFlashCFI01),
@@ -277,10 +310,9 @@ static uint32_t pflash_read(PFlashCFI01 *pfl, hwaddr 
offset,
         /* This should never happen : reset state & treat it as a read */
         DPRINTF("%s: unknown command state: %x\n", __func__, pfl->cmd);
         pfl->wcycle = 0;
-        pfl->cmd = 0;
+        pfl->cmd = 0xff;
         /* fall through to read code */
-    case 0x00:
-        /* Flash area read */
+    case 0xff: /* Read Array */
         ret = pflash_data_read(pfl, offset, width, be);
         break;
     case 0x10: /* Single byte program */
@@ -448,8 +480,6 @@ static void pflash_write(PFlashCFI01 *pfl, hwaddr offset,
     case 0:
         /* read mode */
         switch (cmd) {
-        case 0x00: /* ??? */
-            goto reset_flash;
         case 0x10: /* Single Byte Program */
         case 0x40: /* Single Byte Program */
             DPRINTF("%s: Single Byte Program\n", __func__);
@@ -526,7 +556,7 @@ static void pflash_write(PFlashCFI01 *pfl, hwaddr offset,
             if (cmd == 0xd0) { /* confirm */
                 pfl->wcycle = 0;
                 pfl->status |= 0x80;
-            } else if (cmd == 0xff) { /* read array mode */
+            } else if (cmd == 0xff) { /* Read Array */
                 goto reset_flash;
             } else
                 goto error_flash;
@@ -553,7 +583,7 @@ static void pflash_write(PFlashCFI01 *pfl, hwaddr offset,
             } else if (cmd == 0x01) {
                 pfl->wcycle = 0;
                 pfl->status |= 0x80;
-            } else if (cmd == 0xff) {
+            } else if (cmd == 0xff) { /* read array mode */
                 goto reset_flash;
             } else {
                 DPRINTF("%s: Unknown (un)locking command\n", __func__);
@@ -645,7 +675,7 @@ static void pflash_write(PFlashCFI01 *pfl, hwaddr offset,
     trace_pflash_reset();
     memory_region_rom_device_set_romd(&pfl->mem, true);
     pfl->wcycle = 0;
-    pfl->cmd = 0;
+    pfl->cmd = 0xff;
 }
 
 
@@ -761,7 +791,7 @@ static void pflash_cfi01_realize(DeviceState *dev, Error 
**errp)
     }
 
     pfl->wcycle = 0;
-    pfl->cmd = 0;
+    pfl->cmd = 0xff;
     pfl->status = 0;
     /* Hardcoded CFI table */
     /* Standard "QRY" string */
@@ -1001,5 +1031,14 @@ static int pflash_post_load(void *opaque, int version_id)
         pfl->vmstate = qemu_add_vm_change_state_handler(postload_update_cb,
                                                         pfl);
     }
+
+    /*
+     * Previous to QEMU v4.1 an incorrect value of 0x00 was used for the
+     * READ_ARRAY command.
+     */
+    if (pfl->cmd == 0x00) {
+        pfl->cmd = 0xff;
+    }
+
     return 0;
 }
-- 
2.20.1




reply via email to

[Prev in Thread] Current Thread [Next in Thread]