[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Qemu-devel] [PATCH v2 2/9] hw/block/pflash_cfi01: Use the correct R
From: |
John Snow |
Subject: |
Re: [Qemu-devel] [PATCH v2 2/9] hw/block/pflash_cfi01: Use the correct READ_ARRAY value |
Date: |
Mon, 1 Jul 2019 22:54:42 -0400 |
User-agent: |
Mozilla/5.0 (X11; Linux x86_64; rv:60.0) Gecko/20100101 Thunderbird/60.7.2 |
On 7/1/19 8:12 PM, Philippe Mathieu-Daudé wrote:
> In the "Read Array Flowchart" the command has a value of 0xFF.
>
> In the document [*] the "Read Array Flowchart", the READ_ARRAY
> command has a value of 0xff.
>
> Use the correct value in the pflash model.
>
> There is no change of behavior in the guest, because:
> - when the guest were sending 0xFF, the reset_flash label
> was setting the command value as 0x00
> - 0x00 was used internally for READ_ARRAY
>
> [*] "Common Flash Interface (CFI) and Command Sets"
> (Intel Application Note 646)
> Appendix B "Basic Command Set"
>
> Signed-off-by: Philippe Mathieu-Daudé <address@hidden>
I'm assuming you tested a guest and saw it sending 0xFF; and based
entirely on the assumption that you tested this and it is not now worse:
Reviewed-by: John Snow <address@hidden>
> ---
> hw/block/pflash_cfi01.c | 15 ++++++---------
> 1 file changed, 6 insertions(+), 9 deletions(-)
>
> diff --git a/hw/block/pflash_cfi01.c b/hw/block/pflash_cfi01.c
> index dcc9885bf0..743b5d5794 100644
> --- a/hw/block/pflash_cfi01.c
> +++ b/hw/block/pflash_cfi01.c
> @@ -280,10 +280,9 @@ static uint32_t pflash_read(PFlashCFI01 *pfl, hwaddr
> offset,
> /* This should never happen : reset state & treat it as a read */
> DPRINTF("%s: unknown command state: %x\n", __func__, pfl->cmd);
> pfl->wcycle = 0;
> - pfl->cmd = 0;
> + pfl->cmd = 0xff;
> /* fall through to read code */
> - case 0x00:
> - /* Flash area read */
> + case 0xff: /* Read Array */
> ret = pflash_data_read(pfl, offset, width, be);
> break;
> case 0x10: /* Single byte program */
> @@ -449,8 +448,6 @@ static void pflash_write(PFlashCFI01 *pfl, hwaddr offset,
> case 0:
> /* read mode */
> switch (cmd) {
> - case 0x00: /* ??? */
> - goto reset_flash;
> case 0x10: /* Single Byte Program */
> case 0x40: /* Single Byte Program */
> DPRINTF("%s: Single Byte Program\n", __func__);
> @@ -527,7 +524,7 @@ static void pflash_write(PFlashCFI01 *pfl, hwaddr offset,
> if (cmd == 0xd0) { /* confirm */
> pfl->wcycle = 0;
> pfl->status |= 0x80;
> - } else if (cmd == 0xff) { /* read array mode */
> + } else if (cmd == 0xff) { /* Read Array */
> goto reset_flash;
> } else
> goto error_flash;
> @@ -554,7 +551,7 @@ static void pflash_write(PFlashCFI01 *pfl, hwaddr offset,
> } else if (cmd == 0x01) {
> pfl->wcycle = 0;
> pfl->status |= 0x80;
> - } else if (cmd == 0xff) {
> + } else if (cmd == 0xff) { /* read array mode */
> goto reset_flash;
> } else {
> DPRINTF("%s: Unknown (un)locking command\n", __func__);
> @@ -646,7 +643,7 @@ static void pflash_write(PFlashCFI01 *pfl, hwaddr offset,
> trace_pflash_reset();
> memory_region_rom_device_set_romd(&pfl->mem, true);
> pfl->wcycle = 0;
> - pfl->cmd = 0;
> + pfl->cmd = 0xff;
> }
>
>
> @@ -762,7 +759,7 @@ static void pflash_cfi01_realize(DeviceState *dev, Error
> **errp)
> }
>
> pfl->wcycle = 0;
> - pfl->cmd = 0;
> + pfl->cmd = 0xff;
> pfl->status = 0;
> /* Hardcoded CFI table */
> /* Standard "QRY" string */
>
--
—js
- [Qemu-devel] [PATCH v2 0/9] hw/block/pflash_cfi01: Add DeviceReset() handler, Philippe Mathieu-Daudé, 2019/07/01
- [Qemu-devel] [PATCH v2 1/9] hw/block/pflash_cfi01: Removed an unused timer, Philippe Mathieu-Daudé, 2019/07/01
- [Qemu-devel] [PATCH v2 2/9] hw/block/pflash_cfi01: Use the correct READ_ARRAY value, Philippe Mathieu-Daudé, 2019/07/01
- [Qemu-devel] [PATCH v2 3/9] hw/block/pflash_cfi01: Extract pflash_mode_read_array(), Philippe Mathieu-Daudé, 2019/07/01
- [Qemu-devel] [PATCH v2 4/9] hw/block/pflash_cfi01: Start state machine as READY to accept commands, Philippe Mathieu-Daudé, 2019/07/01
- [Qemu-devel] [PATCH v2 5/9] hw/block/pflash_cfi01: Add the DeviceReset() handler, Philippe Mathieu-Daudé, 2019/07/01