Re: [Qemu-devel] [PATCH for-4.0 3/3] block: test block-stream with a base node that is used by block-commit

[Vladimir Sementsov-Ogievskiy]

26.03.2019 20:07, Alberto Garcia wrote:
> The base node of a block-stream operation indicates the first image
> from the backing chain starting from which no data is copied to the
> top node.
> 
> The block-stream job allows others to use that base image, so a second
> block-stream job could be writing to it at the same time. An important
> restriction is that the base image must not disappear while the stream
> job is ongoing. stream_start() freezes the backing chain from top to
> base with that purpose but it does it too late in the code so there is
> a race condition there.
> 
> This bug was fixed in the previous commit, and this patch contains an
> iotest for this scenario.
> 
> Signed-off-by: Alberto Garcia <address@hidden>
> ---
>   tests/qemu-iotests/030     | 32 ++++++++++++++++++++++++++++++++
>   tests/qemu-iotests/030.out |  4 ++--
>   2 files changed, 34 insertions(+), 2 deletions(-)
> 
> diff --git a/tests/qemu-iotests/030 b/tests/qemu-iotests/030
> index 276e06b5ba..184a59d465 100755
> --- a/tests/qemu-iotests/030
> +++ b/tests/qemu-iotests/030
> @@ -314,6 +314,38 @@ class TestParallelOps(iotests.QMPTestCase):
>   
>           self.wait_until_completed(drive='commit-drive0')
>   
> +    # In this case the base node of the stream job is the same as the
> +    # top node of commit job. Since block-commit removes the top node
> +    # when it finishes, this is not allowed.
> +    def test_overlapping_4(self):
> +        self.assert_no_active_block_jobs()
> +
> +        # Commit from node2 into node0
> +        result = self.vm.qmp('block-commit', device='drive0', 
> top=self.imgs[2], base=self.imgs[0])
> +        self.assert_qmp(result, 'return', {})
> +
> +        # Stream from node2 into node4
> +        result = self.vm.qmp('block-stream', device='node4', 
> base_node='node2', job_id='node4')
> +        self.assert_qmp(result, 'error/class', 'GenericError')
> +
> +        # Wait for all jobs to be finished.

what about use just
self.cancel_and_wait() or self.wait_until_completed() here?

> +        pending_jobs = ['drive0']
> +        while len(pending_jobs) > 0:
> +            for event in self.vm.get_qmp_events(wait=True):
> +                if event['event'] == 'BLOCK_JOB_COMPLETED':
> +                    node_name = self.dictpath(event, 'data/device')
> +                    self.assertTrue(node_name in pending_jobs)
> +                    self.assert_qmp_absent(event, 'data/error')
> +                    pending_jobs.remove(node_name)
> +                if event['event'] == 'BLOCK_JOB_READY':
> +                    self.assert_qmp(event, 'data/device', 'drive0')
> +                    self.assert_qmp(event, 'data/type', 'commit')
> +                    self.assert_qmp_absent(event, 'data/error')
> +                    self.assertTrue('drive0' in pending_jobs)
> +                    self.vm.qmp('block-job-complete', device='drive0')
> +
> +        self.assert_no_active_block_jobs()
> +
>       # Test a block-stream and a block-commit job in parallel
>       # Here the stream job is supposed to finish quickly in order to 
> reproduce
>       # the scenario that triggers the bug fixed in 3d5d319e1221 and 
> 1a63a907507
> diff --git a/tests/qemu-iotests/030.out b/tests/qemu-iotests/030.out
> index 42314e9c00..4fd1c2dcd2 100644
> --- a/tests/qemu-iotests/030.out
> +++ b/tests/qemu-iotests/030.out
> @@ -1,5 +1,5 @@
> -........................
> +.........................
>   ----------------------------------------------------------------------
> -Ran 24 tests
> +Ran 25 tests
>   
>   OK
> 


-- 
Best regards,
Vladimir