qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Qemu-devel] [PULL 2/6] nrf51_gpio: reflect pull-up/pull-down to IRQs


From: Peter Maydell
Subject: [Qemu-devel] [PULL 2/6] nrf51_gpio: reflect pull-up/pull-down to IRQs
Date: Mon, 25 Mar 2019 14:31:48 +0000

From: Paolo Bonzini <address@hidden>

Some drivers do I2C bitbanging by keeping the output to 0 and flipping
the GPIO direction between input and output (see for example in Linux
gpio_set_open_drain_value_commit, in drivers/gpio/gpiolib.c).
When the GPIO is set to input, the pull-up resistor brings the output
to 1, while when the GPIO is set to output, the output driver brings
the output to 0.

Implement this for the nRF51 GPIO device model.  First, if both input and
output are floating, and there is a pull-up or pull-down resistor
configured, do not just set s->in, but also make any devices listening
on the output qemu_irq receive that value.  Second, if the pin is
driven both internally (output pin) and externally you don't get a
short circuit if both sides drive the pin to the same value.

Signed-off-by: Paolo Bonzini <address@hidden>
Acked-by: Stefan Hajnoczi <address@hidden>
Message-id: address@hidden
[PMM: wrapped long line]
Reviewed-by: Peter Maydell <address@hidden>
Signed-off-by: Peter Maydell <address@hidden>
---
 hw/gpio/nrf51_gpio.c | 65 +++++++++++++++++++++++++++-----------------
 1 file changed, 40 insertions(+), 25 deletions(-)

diff --git a/hw/gpio/nrf51_gpio.c b/hw/gpio/nrf51_gpio.c
index 86e047d649f..87a2f2a0dc3 100644
--- a/hw/gpio/nrf51_gpio.c
+++ b/hw/gpio/nrf51_gpio.c
@@ -43,6 +43,17 @@ static bool is_connected(uint32_t config, uint32_t level)
     return state;
 }
 
+static int pull_value(uint32_t config)
+{
+    int pull = extract32(config, 2, 2);
+    if (pull == NRF51_GPIO_PULLDOWN) {
+        return 0;
+    } else if (pull == NRF51_GPIO_PULLUP) {
+        return 1;
+    }
+    return -1;
+}
+
 static void update_output_irq(NRF51GPIOState *s, size_t i,
                               bool connected, bool level)
 {
@@ -61,43 +72,47 @@ static void update_output_irq(NRF51GPIOState *s, size_t i,
 
 static void update_state(NRF51GPIOState *s)
 {
-    uint32_t pull;
+    int pull;
     size_t i;
-    bool connected_out, dir, connected_in, out, input;
+    bool connected_out, dir, connected_in, out, in, input;
 
     for (i = 0; i < NRF51_GPIO_PINS; i++) {
-        pull = extract32(s->cnf[i], 2, 2);
+        pull = pull_value(s->cnf[i]);
         dir = extract32(s->cnf[i], 0, 1);
         connected_in = extract32(s->in_mask, i, 1);
         out = extract32(s->out, i, 1);
+        in = extract32(s->in, i, 1);
         input = !extract32(s->cnf[i], 1, 1);
         connected_out = is_connected(s->cnf[i], out) && dir;
 
-        update_output_irq(s, i, connected_out, out);
-
-        /* Pin both driven externally and internally */
-        if (connected_out && connected_in) {
-            qemu_log_mask(LOG_GUEST_ERROR, "GPIO pin %zu short circuited\n", 
i);
-        }
-
-        /*
-         * Input buffer disconnected from internal/external drives, so
-         * pull-up/pull-down becomes relevant
-         */
-        if (!input || (input && !connected_in && !connected_out)) {
-            if (pull == NRF51_GPIO_PULLDOWN) {
-                s->in = deposit32(s->in, i, 1, 0);
-            } else if (pull == NRF51_GPIO_PULLUP) {
-                s->in = deposit32(s->in, i, 1, 1);
+        if (!input) {
+            if (pull >= 0) {
+                /* Input buffer disconnected from external drives */
+                s->in = deposit32(s->in, i, 1, pull);
+            }
+        } else {
+            if (connected_out && connected_in && out != in) {
+                /* Pin both driven externally and internally */
+                qemu_log_mask(LOG_GUEST_ERROR,
+                              "GPIO pin %zu short circuited\n", i);
+            }
+            if (!connected_in) {
+                /*
+                 * Floating input: the output stimulates IN if connected,
+                 * otherwise pull-up/pull-down resistors put a value on both
+                 * IN and OUT.
+                 */
+                if (pull >= 0 && !connected_out) {
+                    connected_out = true;
+                    out = pull;
+                }
+                if (connected_out) {
+                    s->in = deposit32(s->in, i, 1, out);
+                }
             }
         }
-
-        /* Self stimulation through internal output driver */
-        if (connected_out && !connected_in && input) {
-            s->in = deposit32(s->in, i, 1, out);
-        }
+        update_output_irq(s, i, connected_out, out);
     }
-
 }
 
 /*
-- 
2.20.1




reply via email to

[Prev in Thread] Current Thread [Next in Thread]