[Qemu-devel] [PATCH 1/3] aspeed/i2c: interrupts should be cleared by software only

[Cédric Le Goater]

and the bus interrupt should be lowered when all interrupts have been
cleared. Also, the model does not implement correctly the RX_DONE bit
behavior which should be cleared to allow more data to be received.
Yet to be fixed.

Signed-off-by: Cédric Le Goater <address@hidden>
---
 hw/i2c/aspeed_i2c.c | 21 +++++++++++++++++----
 1 file changed, 17 insertions(+), 4 deletions(-)

diff --git a/hw/i2c/aspeed_i2c.c b/hw/i2c/aspeed_i2c.c
index c762c7366ad9..de6b08378675 100644
--- a/hw/i2c/aspeed_i2c.c
+++ b/hw/i2c/aspeed_i2c.c
@@ -52,6 +52,13 @@
 #define I2CD_AC_TIMING_REG2     0x08       /* Clock and AC Timing Control #1 */
 #define I2CD_INTR_CTRL_REG      0x0c       /* I2CD Interrupt Control */
 #define I2CD_INTR_STS_REG       0x10       /* I2CD Interrupt Status */
+
+#define   I2CD_INTR_SLAVE_ADDR_MATCH       (0x1 << 31) /* 0: addr1 1: addr2 */
+#define   I2CD_INTR_SLAVE_ADDR_RX_PENDING  (0x1 << 30)
+/* bits[19-16] Reserved */
+
+/* All bits below are cleared by writing 1 */
+#define   I2CD_INTR_SLAVE_INACTIVE_TIMEOUT (0x1 << 15)
 #define   I2CD_INTR_SDA_DL_TIMEOUT         (0x1 << 14)
 #define   I2CD_INTR_BUS_RECOVER_DONE       (0x1 << 13)
 #define   I2CD_INTR_SMBUS_ALERT            (0x1 << 12) /* Bus [0-3] only */
@@ -59,11 +66,16 @@
 #define   I2CD_INTR_SMBUS_DEV_ALERT_ADDR   (0x1 << 10) /* Removed */
 #define   I2CD_INTR_SMBUS_DEF_ADDR         (0x1 << 9)  /* Removed */
 #define   I2CD_INTR_GCALL_ADDR             (0x1 << 8)  /* Removed */
-#define   I2CD_INTR_SLAVE_MATCH            (0x1 << 7)  /* use RX_DONE */
+#define   I2CD_INTR_SLAVE_ADDR_RX_MATCH    (0x1 << 7)  /* use RX_DONE */
 #define   I2CD_INTR_SCL_TIMEOUT            (0x1 << 6)
 #define   I2CD_INTR_ABNORMAL               (0x1 << 5)
 #define   I2CD_INTR_NORMAL_STOP            (0x1 << 4)
 #define   I2CD_INTR_ARBIT_LOSS             (0x1 << 3)
+
+/*
+ * TODO: handle correctly I2CD_INTR_RX_DONE which needs to be cleared
+ * to allow next data to be received.
+ */
 #define   I2CD_INTR_RX_DONE                (0x1 << 2)
 #define   I2CD_INTR_TX_NAK                 (0x1 << 1)
 #define   I2CD_INTR_TX_ACK                 (0x1 << 0)
@@ -188,7 +200,6 @@ static void aspeed_i2c_bus_handle_cmd(AspeedI2CBus *bus, 
uint64_t value)
 {
     bus->cmd &= ~0xFFFF;
     bus->cmd |= value & 0xFFFF;
-    bus->intr_status = 0;
 
     if (bus->cmd & I2CD_M_START_CMD) {
         uint8_t state = aspeed_i2c_get_state(bus) & I2CD_MACTIVE ?
@@ -284,8 +295,10 @@ static void aspeed_i2c_bus_write(void *opaque, hwaddr 
offset,
         break;
     case I2CD_INTR_STS_REG:
         bus->intr_status &= ~(value & 0x7FFF);
-        bus->controller->intr_status &= ~(1 << bus->id);
-        qemu_irq_lower(bus->controller->irq);
+        if (!bus->intr_status) {
+            bus->controller->intr_status &= ~(1 << bus->id);
+            qemu_irq_lower(bus->controller->irq);
+        }
         break;
     case I2CD_DEV_ADDR_REG:
         qemu_log_mask(LOG_UNIMP, "%s: slave mode not implemented\n",
-- 
2.17.1