[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Qemu-devel] [PATCH v3] scsi: esp: check TI buffer index before read/wri
From: |
P J P |
Subject: |
[Qemu-devel] [PATCH v3] scsi: esp: check TI buffer index before read/write |
Date: |
Mon, 6 Jun 2016 22:04:43 +0530 |
From: Prasad J Pandit <address@hidden>
The 53C9X Fast SCSI Controller(FSC) comes with internal 16-byte
FIFO buffers. One is used to handle commands and other is for
information transfer. Three control variables 'ti_rptr',
'ti_wptr' and 'ti_size' are used to control r/w access to the
information transfer buffer ti_buf[TI_BUFSZ=16]. In that,
'ti_rptr' is used as read index, where read occurs.
'ti_wptr' is a write index, where write would occur.
'ti_size' indicates total bytes to be read from the buffer.
While reading/writing to this buffer, index could exceed its
size. Add check to avoid OOB r/w access.
Reported-by: Huawei PSIRT <address@hidden>
Reported-by: Li Qiang <address@hidden>
Signed-off-by: Prasad J Pandit <address@hidden>
---
hw/scsi/esp.c | 20 +++++++++-----------
1 file changed, 9 insertions(+), 11 deletions(-)
Update as per:
-> https://lists.gnu.org/archive/html/qemu-devel/2016-06/msg01326.html
diff --git a/hw/scsi/esp.c b/hw/scsi/esp.c
index c2f6f8f..4b94bbc 100644
--- a/hw/scsi/esp.c
+++ b/hw/scsi/esp.c
@@ -403,19 +403,17 @@ uint64_t esp_reg_read(ESPState *s, uint32_t saddr)
trace_esp_mem_readb(saddr, s->rregs[saddr]);
switch (saddr) {
case ESP_FIFO:
- if (s->ti_size > 0) {
+ if ((s->rregs[ESP_RSTAT] & STAT_PIO_MASK) == 0) {
+ /* Data out. */
+ qemu_log_mask(LOG_UNIMP, "esp: PIO data read not implemented\n");
+ s->rregs[ESP_FIFO] = 0;
+ esp_raise_irq(s);
+ } else if (s->ti_rptr < s->ti_wptr) {
s->ti_size--;
- if ((s->rregs[ESP_RSTAT] & STAT_PIO_MASK) == 0) {
- /* Data out. */
- qemu_log_mask(LOG_UNIMP,
- "esp: PIO data read not implemented\n");
- s->rregs[ESP_FIFO] = 0;
- } else {
- s->rregs[ESP_FIFO] = s->ti_buf[s->ti_rptr++];
- }
+ s->rregs[ESP_FIFO] = s->ti_buf[s->ti_rptr++];
esp_raise_irq(s);
}
- if (s->ti_size == 0) {
+ if (s->ti_rptr == s->ti_wptr) {
s->ti_rptr = 0;
s->ti_wptr = 0;
}
@@ -459,7 +457,7 @@ void esp_reg_write(ESPState *s, uint32_t saddr, uint64_t
val)
} else {
trace_esp_error_fifo_overrun();
}
- } else if (s->ti_size == TI_BUFSZ - 1) {
+ } else if (s->ti_wptr == TI_BUFSZ - 1) {
trace_esp_error_fifo_overrun();
} else {
s->ti_size++;
--
2.5.5
- [Qemu-devel] [PATCH v3] scsi: esp: check TI buffer index before read/write,
P J P <=