qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Qemu-devel] [PULL 19/19] ahci: do not remap clb/fis unconditionally


From: John Snow
Subject: [Qemu-devel] [PULL 19/19] ahci: do not remap clb/fis unconditionally
Date: Fri, 22 May 2015 15:59:52 -0400

This continues the IOMMU fix from 2.3, where we should not attempt
to remap the CLB or FIS RX buffers if the AHCI device is currently
running.

The same applies to migration: keep our mitts off these registers
unless the device is supposed to be on.

Does not impact backwards compatibility for the AHCI device.

Signed-off-by: John Snow <address@hidden>
Reviewed-by: Stefan Hajnoczi <address@hidden>
Message-id: address@hidden
---
 hw/ide/ahci.c | 88 ++++++++++++++++++++++++++++++++++++++++++-----------------
 1 file changed, 63 insertions(+), 25 deletions(-)

diff --git a/hw/ide/ahci.c b/hw/ide/ahci.c
index 8e36dec..9e5d862 100644
--- a/hw/ide/ahci.c
+++ b/hw/ide/ahci.c
@@ -198,6 +198,61 @@ static void map_page(AddressSpace *as, uint8_t **ptr, 
uint64_t addr,
     }
 }
 
+/**
+ * Check the cmd register to see if we should start or stop
+ * the DMA or FIS RX engines.
+ *
+ * @ad: Device to engage.
+ * @allow_stop: Allow device to transition from started to stopped?
+ *   'no' is useful for migration post_load, which does not expect a 
transition.
+ *
+ * @return 0 on success, -1 on error.
+ */
+static int ahci_cond_start_engines(AHCIDevice *ad, bool allow_stop)
+{
+    AHCIPortRegs *pr = &ad->port_regs;
+
+    if (pr->cmd & PORT_CMD_START) {
+        if (ahci_map_clb_address(ad)) {
+            pr->cmd |= PORT_CMD_LIST_ON;
+        } else {
+            error_report("AHCI: Failed to start DMA engine: "
+                         "bad command list buffer address");
+            return -1;
+        }
+    } else if (pr->cmd & PORT_CMD_LIST_ON) {
+        if (allow_stop) {
+            ahci_unmap_clb_address(ad);
+            pr->cmd = pr->cmd & ~(PORT_CMD_LIST_ON);
+        } else {
+            error_report("AHCI: DMA engine should be off, "
+                         "but appears to still be running");
+            return -1;
+        }
+    }
+
+    if (pr->cmd & PORT_CMD_FIS_RX) {
+        if (ahci_map_fis_address(ad)) {
+            pr->cmd |= PORT_CMD_FIS_ON;
+        } else {
+            error_report("AHCI: Failed to start FIS receive engine: "
+                         "bad FIS receive buffer address");
+            return -1;
+        }
+    } else if (pr->cmd & PORT_CMD_FIS_ON) {
+        if (allow_stop) {
+            ahci_unmap_fis_address(ad);
+            pr->cmd = pr->cmd & ~(PORT_CMD_FIS_ON);
+        } else {
+            error_report("AHCI: FIS receive engine should be off, "
+                         "but appears to still be running");
+            return -1;
+        }
+    }
+
+    return 0;
+}
+
 static void  ahci_port_write(AHCIState *s, int port, int offset, uint32_t val)
 {
     AHCIPortRegs *pr = &s->dev[port].port_regs;
@@ -229,29 +284,8 @@ static void  ahci_port_write(AHCIState *s, int port, int 
offset, uint32_t val)
              * including LIST_ON and FIS_ON. */
             pr->cmd = (pr->cmd & PORT_CMD_RO_MASK) | (val & ~PORT_CMD_RO_MASK);
 
-            if (pr->cmd & PORT_CMD_START) {
-                if (ahci_map_clb_address(&s->dev[port])) {
-                    pr->cmd |= PORT_CMD_LIST_ON;
-                } else {
-                    error_report("AHCI: Failed to start DMA engine: "
-                                 "bad command list buffer address");
-                }
-            } else if (pr->cmd & PORT_CMD_LIST_ON) {
-                ahci_unmap_clb_address(&s->dev[port]);
-                pr->cmd = pr->cmd & ~(PORT_CMD_LIST_ON);
-            }
-
-            if (pr->cmd & PORT_CMD_FIS_RX) {
-                if (ahci_map_fis_address(&s->dev[port])) {
-                    pr->cmd |= PORT_CMD_FIS_ON;
-                } else {
-                    error_report("AHCI: Failed to start FIS receive engine: "
-                                 "bad FIS receive buffer address");
-                }
-            } else if (pr->cmd & PORT_CMD_FIS_ON) {
-                ahci_unmap_fis_address(&s->dev[port]);
-                pr->cmd = pr->cmd & ~(PORT_CMD_FIS_ON);
-            }
+            /* Check FIS RX and CLB engines, allow transition to false: */
+            ahci_cond_start_engines(&s->dev[port], true);
 
             /* XXX usually the FIS would be pending on the bus here and
                    issuing deferred until the OS enables FIS receival.
@@ -1404,8 +1438,12 @@ static int ahci_state_post_load(void *opaque, int 
version_id)
     for (i = 0; i < s->ports; i++) {
         ad = &s->dev[i];
 
-        ahci_map_clb_address(ad);
-        ahci_map_fis_address(ad);
+        /* Only remap the CLB address if appropriate, disallowing a state
+         * transition from 'on' to 'off' it should be consistent here. */
+        if (ahci_cond_start_engines(ad, false) != 0) {
+            return -1;
+        }
+
         /*
          * If an error is present, ad->busy_slot will be valid and not -1.
          * In this case, an operation is waiting to resume and will re-check
-- 
2.1.0




reply via email to

[Prev in Thread] Current Thread [Next in Thread]