qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Qemu-devel] [PATCH 01/20] eepro100: Fix compiler errors from debug


From: Anthony Liguori
Subject: Re: [Qemu-devel] [PATCH 01/20] eepro100: Fix compiler errors from debug messages
Date: Fri, 19 Feb 2010 15:05:50 -0600
User-agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US; rv:1.9.1.5) Gecko/20091209 Fedora/3.0-4.fc12 Lightning/1.0pre Thunderbird/3.0

On 02/14/2010 10:16 AM, Stefan Weil wrote:
When debug output was enabled (by defining DEBUG_EEPRO100),
some debug messages resulted in a compiler error.

This is fixed here.

Signed-off-by: Stefan Weil<address@hidden>

Michael,

Can you take these through your tree?

Regards,

Anthony Liguori

---
  hw/eepro100.c |   13 +++++++------
  1 files changed, 7 insertions(+), 6 deletions(-)

diff --git a/hw/eepro100.c b/hw/eepro100.c
index b33dbb8..6580ca8 100644
--- a/hw/eepro100.c
+++ b/hw/eepro100.c
@@ -56,7 +56,9 @@
  #define KiB 1024

  /* Debug EEPRO100 card. */
-//~ #define DEBUG_EEPRO100
+#if 0
+# define DEBUG_EEPRO100
+#endif

  #ifdef DEBUG_EEPRO100
  #define logout(fmt, ...) fprintf(stderr, "EE100\t%-24s" fmt, __func__, ## 
__VA_ARGS__)
@@ -874,9 +876,8 @@ static void action_command(EEPRO100State *s)
          cpu_physical_memory_read(s->cb_address, (uint8_t *)&s->tx, 
sizeof(s->tx));
          uint16_t status = le16_to_cpu(s->tx.status);
          uint16_t command = le16_to_cpu(s->tx.command);
-        logout
-            ("val=0x%02x (cu start), status=0x%04x, command=0x%04x, 
link=0x%08x\n",
-             val, status, command, s->tx.link);
+        logout("val=(cu start), status=0x%04x, command=0x%04x, link=0x%08x\n",
+               status, command, s->tx.link);
          bool bit_el = ((command&  0x8000) != 0);
          bool bit_s = ((command&  0x4000) != 0);
          bool bit_i = ((command&  0x2000) != 0);
@@ -891,7 +892,7 @@ static void action_command(EEPRO100State *s)
              break;
          case CmdIASetup:
              cpu_physical_memory_read(s->cb_address + 8,&s->conf.macaddr.a[0], 
6);
-            TRACE(OTHER, logout("macaddr: %s\n", nic_dump(&s->macaddr[0], 6)));
+            TRACE(OTHER, logout("macaddr: %s\n", 
nic_dump(&s->conf.macaddr.a[0], 6)));
              break;
          case CmdConfigure:
              cpu_physical_memory_read(s->cb_address + 8,&s->configuration[0],
@@ -1875,7 +1876,7 @@ static int nic_init(PCIDevice *pci_dev, uint32_t device)
                             pci_mmio_map);

      qemu_macaddr_default_if_unset(&s->conf.macaddr);
-    logout("macaddr: %s\n", nic_dump(&s->macaddr[0], 6));
+    logout("macaddr: %s\n", nic_dump(&s->conf.macaddr.a[0], 6));
      assert(s->region[1] == 0);

      nic_reset(s);





reply via email to

[Prev in Thread] Current Thread [Next in Thread]