[PATCH v2 10/12] hw/block/pflash_cfi01: Extract pflash_mode_read_array()

[Philippe Mathieu-Daudé]

The same pattern is used when setting the flash in READ_ARRAY mode:
- Set the state machine command to READ_ARRAY
- Reset the write_cycle counter
- Reset the memory region in ROMD

Refactor the current code by extracting this pattern.
It is used three times:

- On a read access (on invalid command).

- On a write access (on command failure, error, or explicitly asked)

- When the device is initialized. Here the ROMD mode is hidden
  by the memory_region_init_rom_device() call.

Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
---
 hw/block/pflash_cfi01.c | 40 +++++++++++++++++-----------------------
 1 file changed, 17 insertions(+), 23 deletions(-)

diff --git a/hw/block/pflash_cfi01.c b/hw/block/pflash_cfi01.c
index 2618e00926d..32c9b289715 100644
--- a/hw/block/pflash_cfi01.c
+++ b/hw/block/pflash_cfi01.c
@@ -115,6 +115,19 @@ static const VMStateDescription vmstate_pflash = {
     }
 };
 
+static void pflash_mode_read_array(PFlashCFI01 *pfl)
+{
+    trace_pflash_mode_read_array();
+    /*
+     * The command 0x00 is not assigned by the CFI open standard,
+     * but QEMU historically uses it for the READ_ARRAY command (0xff).
+     */
+    trace_pflash_mode_read_array();
+    pfl->cmd = 0x00;
+    pfl->wcycle = 0;
+    memory_region_rom_device_set_romd(&pfl->mem, true);
+}
+
 /*
  * Perform a CFI query based on the bank width of the flash.
  * If this code is called we know we have a device_width set for
@@ -283,12 +296,7 @@ static uint32_t pflash_read(PFlashCFI01 *pfl, hwaddr 
offset,
     default:
         /* This should never happen : reset state & treat it as a read */
         DPRINTF("%s: unknown command state: %x\n", __func__, pfl->cmd);
-        pfl->wcycle = 0;
-        /*
-         * The command 0x00 is not assigned by the CFI open standard,
-         * but QEMU historically uses it for the READ_ARRAY command (0xff).
-         */
-        pfl->cmd = 0x00;
+        pflash_mode_read_array(pfl);
         /* fall through to read code */
     case 0x00: /* This model reset value for READ_ARRAY (not CFI compliant) */
         /* Flash area read */
@@ -663,10 +671,7 @@ static void pflash_write(PFlashCFI01 *pfl, hwaddr offset,
                   "\n", __func__, offset, pfl->wcycle, pfl->cmd, value);
 
  mode_read_array:
-    trace_pflash_mode_read_array();
-    memory_region_rom_device_set_romd(&pfl->mem, true);
-    pfl->wcycle = 0;
-    pfl->cmd = 0x00; /* This model reset value for READ_ARRAY (not CFI) */
+    pflash_mode_read_array(pfl);
 }
 
 
@@ -872,13 +877,8 @@ static void pflash_cfi01_realize(DeviceState *dev, Error 
**errp)
         pfl->max_device_width = pfl->device_width;
     }
 
-    pfl->wcycle = 0;
-    /*
-     * The command 0x00 is not assigned by the CFI open standard,
-     * but QEMU historically uses it for the READ_ARRAY command (0xff).
-     */
-    pfl->cmd = 0x00;
     pfl->status = 0x80; /* WSM ready */
+    pflash_mode_read_array(pfl);
     pflash_cfi01_fill_cfi_table(pfl);
 }
 
@@ -887,13 +887,7 @@ static void pflash_cfi01_system_reset(DeviceState *dev)
     PFlashCFI01 *pfl = PFLASH_CFI01(dev);
 
     trace_pflash_reset();
-    /*
-     * The command 0x00 is not assigned by the CFI open standard,
-     * but QEMU historically uses it for the READ_ARRAY command (0xff).
-     */
-    pfl->cmd = 0x00;
-    pfl->wcycle = 0;
-    memory_region_rom_device_set_romd(&pfl->mem, true);
+    pflash_mode_read_array(pfl);
     /*
      * The WSM ready timer occurs at most 150ns after system reset.
      * This model deliberately ignores this delay.
-- 
2.26.2