[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Qemu-arm] [PATCH v2 7/9] aspeed: add ast2500 support to scu and sdmc co
|
From: |
Cédric Le Goater |
|
Subject: |
[Qemu-arm] [PATCH v2 7/9] aspeed: add ast2500 support to scu and sdmc controllers |
|
Date: |
Thu, 28 Jul 2016 16:28:17 +0200 |
Based on previous work done by Andrew Jeffery <address@hidden>.
The ast2500 eval board has a hardware strapping register value of
0xF100C2E6 which we use for a definition of AST2500_HW_STRAP1 below.
Signed-off-by: Cédric Le Goater <address@hidden>
---
Andrew,
I did not add your 'Reviewed-by' because of the changes below.
Changes since v1:
- added Hardware strapping register definition for soc AST2500
hw/misc/aspeed_scu.c | 45 ++++++++++++++++++++++++++++++++++-
hw/misc/aspeed_sdmc.c | 1 +
include/hw/misc/aspeed_scu.h | 56 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 101 insertions(+), 1 deletion(-)
diff --git a/hw/misc/aspeed_scu.c b/hw/misc/aspeed_scu.c
index c7e2c8263f55..6dd7e1085420 100644
--- a/hw/misc/aspeed_scu.c
+++ b/hw/misc/aspeed_scu.c
@@ -120,6 +120,41 @@ static const uint32_t
ast2400_a0_resets[ASPEED_SCU_NR_REGS] = {
[BMC_DEV_ID] = 0x00002402U
};
+/* SCU70 bit 23: 0 24Mhz. bit 11:9: 0b001 AXI:ABH ratio 2:1 */
+/* AST2500 revision A1 */
+
+static const uint32_t ast2500_a1_resets[ASPEED_SCU_NR_REGS] = {
+ [SYS_RST_CTRL] = 0xFFCFFEDCU,
+ [CLK_SEL] = 0xF3F40000U,
+ [CLK_STOP_CTRL] = 0x19FC3E8BU,
+ [D2PLL_PARAM] = 0x00026108U,
+ [MPLL_PARAM] = 0x00030291U,
+ [HPLL_PARAM] = 0x93000400U,
+ [MISC_CTRL1] = 0x00000010U,
+ [PCI_CTRL1] = 0x20001A03U,
+ [PCI_CTRL2] = 0x20001A03U,
+ [PCI_CTRL3] = 0x04000030U,
+ [SYS_RST_STATUS] = 0x00000001U,
+ [SOC_SCRATCH1] = 0x000000C0U, /* SoC completed DRAM init */
+ [MISC_CTRL2] = 0x00000023U,
+ [RNG_CTRL] = 0x0000000EU,
+ [PINMUX_CTRL2] = 0x0000F000U,
+ [PINMUX_CTRL3] = 0x03000000U,
+ [PINMUX_CTRL4] = 0x00000000U,
+ [PINMUX_CTRL5] = 0x0000A000U,
+ [WDT_RST_CTRL] = 0x023FFFF3U,
+ [PINMUX_CTRL8] = 0xFFFF0000U,
+ [PINMUX_CTRL9] = 0x000FFFFFU,
+ [FREE_CNTR4] = 0x000000FFU,
+ [FREE_CNTR4_EXT] = 0x000000FFU,
+ [CPU2_BASE_SEG1] = 0x80000000U,
+ [CPU2_BASE_SEG4] = 0x1E600000U,
+ [CPU2_BASE_SEG5] = 0xC0000000U,
+ [UART_HPLL_CLK] = 0x00001903U,
+ [PCIE_CTRL] = 0x0000007BU,
+ [BMC_DEV_ID] = 0x00002402U
+};
+
static uint64_t aspeed_scu_read(void *opaque, hwaddr offset, unsigned size)
{
AspeedSCUState *s = ASPEED_SCU(opaque);
@@ -198,6 +233,10 @@ static void aspeed_scu_reset(DeviceState *dev)
case AST2400_A0_SILICON_REV:
reset = ast2400_a0_resets;
break;
+ case AST2500_A0_SILICON_REV:
+ case AST2500_A1_SILICON_REV:
+ reset = ast2500_a1_resets;
+ break;
default:
g_assert_not_reached();
}
@@ -208,7 +247,11 @@ static void aspeed_scu_reset(DeviceState *dev)
s->regs[HW_STRAP2] = s->hw_strap2;
}
-static uint32_t aspeed_silicon_revs[] = { AST2400_A0_SILICON_REV, };
+static uint32_t aspeed_silicon_revs[] = {
+ AST2400_A0_SILICON_REV,
+ AST2500_A0_SILICON_REV,
+ AST2500_A1_SILICON_REV
+};
bool is_supported_silicon_rev(uint32_t silicon_rev)
{
diff --git a/hw/misc/aspeed_sdmc.c b/hw/misc/aspeed_sdmc.c
index 6cc0301a6331..621d166890fa 100644
--- a/hw/misc/aspeed_sdmc.c
+++ b/hw/misc/aspeed_sdmc.c
@@ -196,6 +196,7 @@ static void aspeed_sdmc_reset(DeviceState *dev)
break;
case AST2500_A0_SILICON_REV:
+ case AST2500_A1_SILICON_REV:
s->regs[R_CONF] |=
ASPEED_SDMC_HW_VERSION(1) |
ASPEED_SDMC_VGA_APERTURE(ASPEED_SDMC_VGA_64MB) |
diff --git a/include/hw/misc/aspeed_scu.h b/include/hw/misc/aspeed_scu.h
index dfc3e023f3ba..d79e2214457d 100644
--- a/include/hw/misc/aspeed_scu.h
+++ b/include/hw/misc/aspeed_scu.h
@@ -33,6 +33,7 @@ typedef struct AspeedSCUState {
#define AST2400_A0_SILICON_REV 0x02000303U
#define AST2500_A0_SILICON_REV 0x04000303U
+#define AST2500_A1_SILICON_REV 0x04010303U
extern bool is_supported_silicon_rev(uint32_t silicon_rev);
@@ -145,4 +146,59 @@ extern bool is_supported_silicon_rev(uint32_t silicon_rev);
SCU_HW_STRAP_VGA_SIZE_SET(VGA_16M_DRAM) | \
SCU_HW_STRAP_BOOT_MODE(SPI_BOOT))
+/*
+ * Hardware strapping register definition (for Aspeed AST2500 SOC and
+ * higher)
+ */
+#define SCU_AST2500_HW_STRAP_SPI_AUTOFETCH_ENABLE (0x1 << 31)
+#define SCU_AST2500_HW_STRAP_GPIO_STRAP_ENABLE (0x1 << 30)
+#define SCU_AST2500_HW_STRAP_UART_DEBUG (0x1 << 29)
+#define UART_DEBUG_UART1 0
+#define UART_DEBUG_UART5 1
+#define SCU_AST2500_HW_STRAP_RESERVED28 (0x1 << 28)
+
+#define SCU_AST2500_HW_STRAP_FAST_RESET_DBG (0x1 << 27)
+#define SCU_AST2500_HW_STRAP_ESPI_FLASH_ENABLE (0x1 << 26)
+#define SCU_AST2500_HW_STRAP_ESPI_ENABLE (0x1 << 25)
+#define SCU_AST2500_HW_STRAP_DDR4_ENABLE (0x1 << 24)
+
+#define SCU_AST2500_HW_STRAP_ACPI_ENABLE (0x1 << 19)
+#define SCU_AST2500_HW_STRAP_USBCKI_FREQ (0x1 << 18)
+#define USBCKI_FREQ_24MHZ 0
+#define USBCKI_FREQ_28MHZ 1
+
+#define SCU_AST2500_HW_STRAP_SET_AXI_AHB_RATIO(x) (x << 9)
+#define SCU_AST2500_HW_STRAP_GET_AXI_AHB_RATIO(x) ((x >> 9) & 7)
+#define SCU_AST2500_HW_STRAP_CPU_AXI_RATIO_MASK (0x7 << 9)
+#define AXI_AHB_RATIO_UNDEFINED 0
+#define AXI_AHB_RATIO_2_1 1
+#define AXI_AHB_RATIO_3_1 2
+#define AXI_AHB_RATIO_4_1 3
+#define AXI_AHB_RATIO_5_1 4
+#define AXI_AHB_RATIO_6_1 5
+#define AXI_AHB_RATIO_7_1 6
+#define AXI_AHB_RATIO_8_1 7
+
+#define SCU_AST2500_HW_STRAP_RESERVED1 (0x1 << 1)
+#define SCU_AST2500_HW_STRAP_DIS_BOOT (0x1 << 0)
+
+#define AST2500_HW_STRAP1_DEFAULTS ( \
+ SCU_AST2500_HW_STRAP_RESERVED28 | \
+ SCU_HW_STRAP_2ND_BOOT_WDT | \
+ SCU_HW_STRAP_VGA_CLASS_CODE | \
+ SCU_HW_STRAP_LPC_RESET_PIN | \
+ SCU_AST2500_HW_STRAP_SET_AXI_AHB_RATIO(AXI_AHB_RATIO_2_1) | \
+ SCU_HW_STRAP_VGA_SIZE_SET(VGA_16M_DRAM) | \
+ SCU_AST2500_HW_STRAP_RESERVED1)
+
+#define AST2500_HW_STRAP1 (( \
+ AST2500_HW_STRAP1_DEFAULTS | \
+ SCU_AST2500_HW_STRAP_SPI_AUTOFETCH_ENABLE | \
+ SCU_AST2500_HW_STRAP_GPIO_STRAP_ENABLE | \
+ SCU_AST2500_HW_STRAP_UART_DEBUG | \
+ SCU_AST2500_HW_STRAP_DDR4_ENABLE | \
+ SCU_HW_STRAP_MAC1_RGMII | \
+ SCU_HW_STRAP_MAC0_RGMII) & \
+ ~SCU_HW_STRAP_2ND_BOOT_WDT)
+
#endif /* ASPEED_SCU_H */
--
2.1.4
- [Qemu-arm] [PATCH v2 0/9] arm: add ast2500 support, Cédric Le Goater, 2016/07/28
- [Qemu-arm] [PATCH v2 1/9] palmetto-bmc: rename file to aspeed.c, Cédric Le Goater, 2016/07/28
- [Qemu-arm] [PATCH v2 2/9] palmetto-bmc: add a "silicon-rev" property at the soc level, Cédric Le Goater, 2016/07/28
- [Qemu-arm] [PATCH v2 3/9] palmetto-bmc: replace palmetto_bmc with aspeed, Cédric Le Goater, 2016/07/28
- [Qemu-arm] [PATCH v2 4/9] ast2400: use machine cpu_model to initialize the soc cpu, Cédric Le Goater, 2016/07/28
- [Qemu-arm] [PATCH v2 5/9] palmetto-bmc: add board specific configuration, Cédric Le Goater, 2016/07/28
- [Qemu-arm] [PATCH v2 6/9] hw/misc: use macros to define hw-strap1 register on Aspeed SOC, Cédric Le Goater, 2016/07/28
- [Qemu-arm] [PATCH v2 7/9] aspeed: add ast2500 support to scu and sdmc controllers,
Cédric Le Goater <=
- [Qemu-arm] [PATCH v2 8/9] arm: add support for an ast2500 evaluation board, Cédric Le Goater, 2016/07/28
- [Qemu-arm] [PATCH v2 9/9] palmetto-bmc: remove extra no_sdcard assignement, Cédric Le Goater, 2016/07/28