☠ Buildbot (Sourceware): gnupoke - failed test (failure) (master)

[builder]

A new failure has been detected on builder gnupoke-ubuntu-riscv while building 
gnupoke.

Full details are available at:
    https://builder.sourceware.org/buildbot/#/builders/281/builds/180

Build state: failed test (failure)
Revision: ae6b8f05e0735cde70d7f605133aa394d8427869
Worker: starfive-2
Build Reason: (unknown)
Blamelist: Jose E. Marchesi <jose.marchesi@oracle.com>

Steps:

- 0: worker_preparation ( success )

- 1: git checkout ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/1/logs/stdio

- 2: bootstrap ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/2/logs/stdio

- 3: configure ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/3/logs/stdio
        - config.log: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/3/logs/config_log

- 4: make ( warnings )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/4/logs/stdio
        - warnings (19): 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/4/logs/warnings__19_

- 5: make check ( warnings )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/5/logs/stdio
        - poke.log: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/5/logs/poke_log
        - warnings (2): 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/5/logs/warnings__2_

- 6: make syntax-check ( failure )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/6/logs/stdio

- 7: prep ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/7/logs/stdio

- 8: build bunsen.cpio.gz ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/8/logs/stdio

- 9: fetch bunsen.cpio.gz ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/9/logs/stdio

- 10: unpack bunsen.cpio.gz ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/10/logs/stdio

- 11: pass .bunsen.source.* ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/11/logs/stdio

- 12: upload to bunsen ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/12/logs/stdio

- 13: clean up ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#/builders/281/builds/180/steps/13/logs/stdio