RE: [Partysip-dev] platform support and sw requirements

[Aymeric Moizard]

Tony,

trace and debug can only be disabled if the
library has been compiled with trace and debug disabled...

I should fix that. :)

As partysip is at a very early development steps, you should
try to compile it with debug and trace actived...

Aymeric

On Thu, 23 May 2002, Toni Barata (EPS) wrote:

> Hi Aymeric,
>
> I have some problems to compile the partysip.
> For the libosip-0.8.6.tar.gz installation procedure I have followed the next
> steps:
>
>   $> tar -xvzf libosip-0.X.X.tar.gz
>   $> mkdir linux-build
>   $> cd linux-build
>   $> ../libosip-0.X.X/configure
>   $> make
>   $> make install
>
> For the partysip-1.4.3.tar.gz installation I have tryed to run this steps:
>
>   $> tar -xvzf partysip-1.4.3.tar.gz
>   $> cd partysip-1.4.3
>   $> ./configure --disable-debug --disable-mleak
>   $> make
>   $> make install
>
> But when I'm in the "make" step I get the folloing error:
>
> main.o: In function `partysip_level':
> main.o(.text+0x2ad): undefined reference to `trace_enable_level'
> main.o(.text+0x2d7): undefined reference to `trace_enable_level'
> main.o(.text+0x301): undefined reference to `trace_enable_level'
> main.o(.text+0x32b): undefined reference to `trace_enable_level'
> main.o(.text+0x355): undefined reference to `trace_enable_level'
> main.o(.text+0x37f): more undefined references to `trace_enable_level'
> follow
> main.o: In function `partysip_level':
> main.o(.text+0x3a9): undefined reference to `trace_disable_level'
> main.o(.text+0x3b6): undefined reference to `trace_disable_level'
> main.o(.text+0x3c3): undefined reference to `trace_disable_level'
> main.o(.text+0x3d0): undefined reference to `trace_disable_level'
> main.o(.text+0x3dd): undefined reference to `trace_disable_level'
> main.o(.text+0x3ea): more undefined references to `trace_disable_level'
> follow
> main.o: In function `main':
> main.o(.text+0xd15): undefined reference to `trace_initialize'
> collect2: ld returned 1 exit status
> make[2]: *** [partysip] Error 1
> make[1]: *** [all-recursive] Error 1
> make: *** [all-recursive-am] Error 2
>
> Could you tell me what is needed to done here.
>
> thanks.
> Tony
>
> -----Original Message-----
> From: Aymeric Moizard [mailto:address@hidden
> Sent: quinta-feira, 23 de Maio de 2002 12:58
> To: Toni Barata (EPS)
> Cc: 'address@hidden'
> Subject: Re: [Partysip-dev] platform support and sw requirements
>
>
>
> Not yet.
> Just ask and take a look at the archive of the mailing list.
>
> Only linux is fully supported and is the only development platform.
> I will focus on a windows port as soon as all required feature
> will be implemented.
>
> A few unresolved issue are happening on solaris. (see previous
> message about the pipe())
>
> Software requirements:
> partysip-0.4.3 (use the CVS if possible)
> osip-0.8.6.tar.gz (0.8.5 should work fine)
> libc
>
> Aymeric
>
> On Thu, 23 May 2002, Toni Barata (EPS) wrote:
>
> > Hi all,
> >
> > Is there any documentation refering the platform support (e.g. Red Hat
> 7.2)
> > and Software requirements before proceeding with the instalations of the
> > PartySip.
> >
> > Regards.
> > Tony
> >
> > _______________________________________________
> > Partysip-dev mailing list
> > address@hidden
> > http://mail.freesoftware.fsf.org/mailman/listinfo/partysip-dev
> >
>