[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
AW: Re: [Paparazzi-devel] LEA-5H NoFix Issue
From: |
address@hidden |
Subject: |
AW: Re: [Paparazzi-devel] LEA-5H NoFix Issue |
Date: |
Fri, 5 Mar 2010 18:59:52 +0000 (GMT) |
Hi there,
Thanks for your reply. Good to hear that it's not a issue with this general
setup.
Got it from PPZUAV, I'm using a 11.1 V LiPo pack to power the TWOG, the GPS
unit is attached to the TWOG via the pins
GND-3.3v-TXD0-RXD0 of the gps plug.
Could you send me the
u-center configuration file of your GPS unit? Just to compare it to mine.
Regards
----Ursprüngliche Nachricht----
Von: address@hidden
Datum: 05.03.2010 17:46
An: <address@hidden>, <address@hidden>
Betreff: Re: [Paparazzi-devel] LEA-5H NoFix Issue
Hi Nicola,
I am not too much experienced in Paparazzi, but my LEA-5H+Sarantel+Twog
works without any problem in spite of the fact that I am using a 7.6V LiPo
accupack. The hardware was shipped by CheBuzz.
Can you describe more detailed the power supply of your GPS?
Balazs
> Hi Pat and thanks alot for your reply,
>
> It seems indeed that the issue is power-supply related, as the current
> indicator on the GCS shows way more
> fluctuation as soon as the GPS starts to look for its servers. Or is that
> normal? See image;
> http://img59.imageshack.us/img59/9461/strangevoltage.jpg
>
>
>
> Notations to the image;
> 1) is without GPS connected... as soon as its connected it looks the same
> but voltage displayed goes up to 11v...
> tiny spikes, no drops
> 2) is the phase where the GPS looks for servers... looks nasty..
> 3) is after 2-3 minutes outside. Still some spikes and drops, but not that
> bad anymore
>
> I tried to change some power supply related settings in u-center, but with
> no success.
>
> Please tell me how you solved your issues Pat, external power supply just
> for the GPS? Are
> we the only SPK-LEA5H+TWOG users out there having this or similar issues?
> If yes, might this be related to defective
> hardware of some kind?
>
>
>
> Regards
>
>
>
> ----UrsprĂźngliche Nachricht----
>
> Von: address@hidden
>
> Datum: 05.03.2010 05:06
>
> An: <address@hidden>, <address@hidden>
>
> Betreff: Re: [Paparazzi-devel] LEA-5H NoFix Issue
>
>
>
> I've had a similar issue with that model GPS: I found, finally, that
>
> the current available from the power supply seems to matter. Check
>
> your power supply and make sure it isn't dipping down too far when you
>
> attach the GPS.
>
>
>
> On Thu, Mar 4, 2010 at 11:25 AM, address@hidden
>
> <address@hidden> wrote:
>
>> Hello everybody,
>
>>
>
>> I'm getting a odd issue when trying to get a GPS Fix in the Paparazzi
>> GCS. In U-center I can get a 3d fix in ca. 30
>
>> secs no issues, but in the GCS it's never able to get a fix. It finds
>> multiple servers, the signal strength goes up
> to
>
>> ~40dB and after a couple seconds the signal dies again and the GCS moves
>> on to the next server over and over again.
> The
>
>> bars stay red until the signal dies, then they turn grey. In u-center
>> the message output looks great (to me), in the
>
>> GCS only some messages do display a value and those are pretty
>> unrealistic.
>
>>
>
>>
>
>>
>
>> This is from my airframe.xml;
>
>>
>
>> [...]
>
>>
>
>> CONFIG = \"tiny_2_1_1.h\"
>
>>
>
>> [...]
>
>>
>
>> ap.CFLAGS += -DGPS -DUBX -DUSE_UART0 -DGPS_LINK=Uart0
>> -DUART0_BAUD=B38400 -DGPS_USE_LATLONG
>
>>
>
>> ap.srcs += gps_ubx.c gps.c latlong.c
>
>>
>
>>
>
>>
>
>> I've tried to:
>
>>
>
>> -reset the GPS module using u-center and load the config file from the
>> Wiki ( http://paparazzi.enac.fr/wiki_images/Tiny_LEA-5H-v5.zip
>
>> ) with no different end result.
>
>>
>> -reset the GPS module and configured everything from hand per the Wiki's
> directions with no different end result.
>> -Flash the different Firmware Updates into the gps receiver ( 5.00 /
>> 6.00 /
> 6.02 )
>
>> with no different end result.
>
>>
>
>>
>
>>
>
>> My setup:
>
>>
>
>> Twog // PPZUAV LEA-5H+active Sarantel Geohelix Antenna
>> //XbeeProSeries2,2.4Ghz
>
>>
>
>>
>
>>
>
>> If someone could explain to me what I'm doing wrong I'd highly
>> appreciate that. I'm stuck since days here.
>
>>
>
>> If I shall post the message view output of u-center or my whole
>> airframe-config file just tell me what you need.
>
>>
>
>>
>
>>
>
>> Regards,
>
>>
>
>>
>
>>
>
>> Nico
>
>>
>
>>
>
>>
>
>> _______________________________________________
>
>> Paparazzi-devel mailing list
>
>> address@hidden
>
>> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>>
>
>
>
>
>
>
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>